diff options
| author | Roger Frank <rfrank@pglaf.org> | 2025-10-15 02:34:26 -0700 |
|---|---|---|
| committer | Roger Frank <rfrank@pglaf.org> | 2025-10-15 02:34:26 -0700 |
| commit | 694acd5cb82097249a901164f716b7a8c9f79138 (patch) | |
| tree | 0484fa2aac8cff24db3491a6035d6145bf4a71c4 /27286-h | |
Diffstat (limited to '27286-h')
| -rw-r--r-- | 27286-h/27286-h.htm | 2266 | ||||
| -rw-r--r-- | 27286-h/images/image1.jpg | bin | 0 -> 53205 bytes | |||
| -rw-r--r-- | 27286-h/images/image10.jpg | bin | 0 -> 19117 bytes | |||
| -rw-r--r-- | 27286-h/images/image11.jpg | bin | 0 -> 88093 bytes | |||
| -rw-r--r-- | 27286-h/images/image12.jpg | bin | 0 -> 73988 bytes | |||
| -rw-r--r-- | 27286-h/images/image13.jpg | bin | 0 -> 43217 bytes | |||
| -rw-r--r-- | 27286-h/images/image14.jpg | bin | 0 -> 17573 bytes | |||
| -rw-r--r-- | 27286-h/images/image15.jpg | bin | 0 -> 46766 bytes | |||
| -rw-r--r-- | 27286-h/images/image16.jpg | bin | 0 -> 54430 bytes | |||
| -rw-r--r-- | 27286-h/images/image17.jpg | bin | 0 -> 53346 bytes | |||
| -rw-r--r-- | 27286-h/images/image18.jpg | bin | 0 -> 38400 bytes | |||
| -rw-r--r-- | 27286-h/images/image19.jpg | bin | 0 -> 34767 bytes | |||
| -rw-r--r-- | 27286-h/images/image2.jpg | bin | 0 -> 43785 bytes | |||
| -rw-r--r-- | 27286-h/images/image20.jpg | bin | 0 -> 48352 bytes | |||
| -rw-r--r-- | 27286-h/images/image21.jpg | bin | 0 -> 48513 bytes | |||
| -rw-r--r-- | 27286-h/images/image22.jpg | bin | 0 -> 79180 bytes | |||
| -rw-r--r-- | 27286-h/images/image23.jpg | bin | 0 -> 57015 bytes | |||
| -rw-r--r-- | 27286-h/images/image24.jpg | bin | 0 -> 59037 bytes | |||
| -rw-r--r-- | 27286-h/images/image25.jpg | bin | 0 -> 67353 bytes | |||
| -rw-r--r-- | 27286-h/images/image26.jpg | bin | 0 -> 38558 bytes | |||
| -rw-r--r-- | 27286-h/images/image27.jpg | bin | 0 -> 26113 bytes | |||
| -rw-r--r-- | 27286-h/images/image28.jpg | bin | 0 -> 29213 bytes | |||
| -rw-r--r-- | 27286-h/images/image29.jpg | bin | 0 -> 29917 bytes | |||
| -rw-r--r-- | 27286-h/images/image3.jpg | bin | 0 -> 15723 bytes | |||
| -rw-r--r-- | 27286-h/images/image30.jpg | bin | 0 -> 18790 bytes | |||
| -rw-r--r-- | 27286-h/images/image31.jpg | bin | 0 -> 35102 bytes | |||
| -rw-r--r-- | 27286-h/images/image32.jpg | bin | 0 -> 26526 bytes | |||
| -rw-r--r-- | 27286-h/images/image33.jpg | bin | 0 -> 20297 bytes | |||
| -rw-r--r-- | 27286-h/images/image34.jpg | bin | 0 -> 29458 bytes | |||
| -rw-r--r-- | 27286-h/images/image35.jpg | bin | 0 -> 13245 bytes | |||
| -rw-r--r-- | 27286-h/images/image36.jpg | bin | 0 -> 27376 bytes | |||
| -rw-r--r-- | 27286-h/images/image37.jpg | bin | 0 -> 13162 bytes | |||
| -rw-r--r-- | 27286-h/images/image38.jpg | bin | 0 -> 22987 bytes | |||
| -rw-r--r-- | 27286-h/images/image39.jpg | bin | 0 -> 23055 bytes | |||
| -rw-r--r-- | 27286-h/images/image4.jpg | bin | 0 -> 17315 bytes | |||
| -rw-r--r-- | 27286-h/images/image40.jpg | bin | 0 -> 20255 bytes | |||
| -rw-r--r-- | 27286-h/images/image40a.jpg | bin | 0 -> 30992 bytes | |||
| -rw-r--r-- | 27286-h/images/image41.jpg | bin | 0 -> 13735 bytes | |||
| -rw-r--r-- | 27286-h/images/image42.jpg | bin | 0 -> 12952 bytes | |||
| -rw-r--r-- | 27286-h/images/image43.jpg | bin | 0 -> 51734 bytes | |||
| -rw-r--r-- | 27286-h/images/image44.jpg | bin | 0 -> 38844 bytes | |||
| -rw-r--r-- | 27286-h/images/image45.jpg | bin | 0 -> 59817 bytes | |||
| -rw-r--r-- | 27286-h/images/image46.jpg | bin | 0 -> 38499 bytes | |||
| -rw-r--r-- | 27286-h/images/image47.jpg | bin | 0 -> 72411 bytes | |||
| -rw-r--r-- | 27286-h/images/image48.jpg | bin | 0 -> 44988 bytes | |||
| -rw-r--r-- | 27286-h/images/image49.jpg | bin | 0 -> 55295 bytes | |||
| -rw-r--r-- | 27286-h/images/image5.jpg | bin | 0 -> 14792 bytes | |||
| -rw-r--r-- | 27286-h/images/image50.jpg | bin | 0 -> 37093 bytes | |||
| -rw-r--r-- | 27286-h/images/image51.jpg | bin | 0 -> 64685 bytes | |||
| -rw-r--r-- | 27286-h/images/image6.jpg | bin | 0 -> 19450 bytes | |||
| -rw-r--r-- | 27286-h/images/image7.jpg | bin | 0 -> 19325 bytes | |||
| -rw-r--r-- | 27286-h/images/image8.jpg | bin | 0 -> 19320 bytes | |||
| -rw-r--r-- | 27286-h/images/image9.jpg | bin | 0 -> 18949 bytes |
53 files changed, 2266 insertions, 0 deletions
diff --git a/27286-h/27286-h.htm b/27286-h/27286-h.htm new file mode 100644 index 0000000..8391a9f --- /dev/null +++ b/27286-h/27286-h.htm @@ -0,0 +1,2266 @@ +<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" + "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd"> + +<html xmlns="http://www.w3.org/1999/xhtml"> + <head> + <meta http-equiv="Content-Type" content="text/html;charset=iso-8859-1" /> + <title> + The Project Gutenberg eBook of Gas and Oil Engines Simply Explained, + by Walter C. Runciman. + </title> + <style type="text/css"> +/*<![CDATA[ XML blockout */ +<!-- + p { margin-top: .75em; text-align: justify; + margin-bottom: .75em; text-indent: 1.25em; + line-height: 130%;} + p.t1 {font-family: courier new, monospace; text-align: center; text-indent: 0em;} + + h1 {text-align: center; clear: both; font-variant: small-caps; + font-weight: normal; letter-spacing: 0.1em;} + h2 {text-align: center; clear: both; font-family: garamond, serif; + font-weight: normal; letter-spacing: 0.1em;} + h3 {text-align: center; clear: both; font-family: garamond, serif; + font-weight: normal;} + + hr { width: 33%; margin-top: 2em; margin-bottom: 2em; + margin-left: auto; margin-right: auto; clear: both; } + + table {margin-left: auto; margin-right: auto;} + + body{margin-left: 10%; margin-right: 10%;} + + .pagenum {display: inline; font-size: 0.9em; text-align: right; + position: absolute; right: 2%; text-indent: 0em; + padding: 1px 2px; font-style: normal; font-family: garamond, serif; + font-variant: normal; font-weight: normal; text-decoration: none; + color: #444; background-color: #FF99CC;} + + .center {text-align: center; text-indent: 0em;} + .right {text-align: right; padding-right: 2em;} + .smcap {font-variant: small-caps;} + .above, .below { font-size: 70%;} + .above { vertical-align: 0.7ex; } + .below { vertical-align: -0.3ex; } + .noin {text-indent: 0em;} + .caption {font-weight: normal; text-indent: 0em;} + + .figcenter {margin: auto; text-align: center; margin-bottom: 1em; margin-top: + 1em;} + + .figleft {float: left; clear: left; margin-left: 1em; margin-bottom: 1em; margin-top: + 1em; margin-right: 1em; padding: 0; text-align: center;} + + .figright {float: right; clear: right; margin-left: 1em; margin-bottom: 1em; + margin-top: 1em; margin-right: 0; padding: 0; text-align: center;} + + + // --> + /* XML end ]]>*/ + </style> + </head> +<body> + + +<pre> + +The Project Gutenberg EBook of Gas and Oil Engines, Simply Explained, by +Walter C. Runciman + +This eBook is for the use of anyone anywhere at no cost and with +almost no restrictions whatsoever. You may copy it, give it away or +re-use it under the terms of the Project Gutenberg License included +with this eBook or online at www.gutenberg.org + + +Title: Gas and Oil Engines, Simply Explained + An Elementary Instruction Book for Amateurs and Engine Attendants + +Author: Walter C. Runciman + +Release Date: November 17, 2008 [EBook #27286] + +Language: English + +Character set encoding: ISO-8859-1 + +*** START OF THIS PROJECT GUTENBERG EBOOK GAS AND OIL ENGINES *** + + + + +Produced by Steven Gibbs, Greg Bergquist and the Online +Distributed Proofreading Team at https://www.pgdp.net + + + + + + +</pre> + + + + + + + +<h1>Gas and Oil Engines<br /> + +<small>SIMPLY EXPLAINED</small></h1> + +<p class="center"><i>An Elementary Instruction Book for Amateurs<br /> +and Engine Attendants</i><br /><br /><br /></p> + + +<p class="center"><small>BY</small><br /> +WALTER C. RUNCIMAN<br /> +<br /> +<br /> +<i>FULLY ILLUSTRATED</i><br /><br /><br /><br /><br /><br /></p> + + +<p class="t1">LONDON<br /><br /> + +Model Engineer Series. The "Model Engineer"<br /> +Series, no. 26.<br /><br /> + +1905</p> + + + +<hr /> +<h2>CONTENTS</h2> + + + + + +<div class='center'> +<table border="0" width="50%" cellpadding="4" cellspacing="0" summary="Contents"> +<tr> + <td align='right'><small>CHAP.</small></td> + <td> </td> + <td align='right'><small>PAGE</small></td></tr> +<tr> + <td> </td> + <td align='left'>PREFACE</td> + <td align='right'><a href="#PREFACE">5</a></td></tr> +<tr> + <td align='right'>I.</td> + <td align='left'>INTRODUCTORY</td> + <td align='right'><a href="#CHAPTER_I">7</a></td> +</tr> +<tr> + <td align='right'>II.</td> + <td align='left'>THE COMPONENT PARTS OF AN ENGINE</td> + <td align='right'><a href="#CHAPTER_II">13</a></td> +</tr> +<tr> + <td align='right'>III.</td> + <td align='left'>HOW A GAS ENGINE WORKS</td> + <td align='right'><a href="#CHAPTER_III">22</a></td> +</tr> +<tr> + <td align='right'>IV.</td> + <td align='left'>IGNITION DEVICES</td> + <td align='right'><a href="#CHAPTER_IV">33</a></td> +</tr> +<tr> + <td align='right'>V.</td> + <td align='left'>MAGNETO IGNITION</td> + <td align='right'><a href="#CHAPTER_V">47</a></td> +</tr> +<tr> + <td align='right'>VI.</td> + <td align='left'>GOVERNING</td> + <td align='right'><a href="#CHAPTER_VI">51</a></td> +</tr> +<tr> + <td align='right'>VII.</td> + <td align='left'>CAMS AND VALVE SETTINGS</td> + <td align='right'><a href="#CHAPTER_VII">63</a></td> +</tr> +<tr> + <td align='right'>VIII.</td> + <td align='left'>OIL ENGINES</td> + <td align='right'><a href="#CHAPTER_VIII">81</a></td> +</tr> +</table></div> + + + +<hr /><p><span class='pagenum'><a name="Page_5" id="Page_5">[Pg 5]</a></span></p> +<h2><a name="PREFACE" id="PREFACE"></a>PREFACE</h2> + + +<p class="noin"><span class="smcap">My</span> object in placing this handbook before the reader is to provide him +with a simple and straightforward explanation of how and why a gas +engine, or an oil engine, works. The main features and peculiarities in +the construction of these engines are described, while the methods and +precautions necessary to arrive at desirable results are detailed as +fully as the limited space permits. I have aimed at supplying just that +information which my experience shows is most needed by the user and by +the amateur builder of small power engines. In place of giving a mere +list of common engine troubles and their remedies, I have thought it +better to endeavour to explain thoroughly the fundamental principles and +essentials of good running, so that should any difficulty arise, the +engine attendant will be able to reason out for himself the cause of the +trouble, and will thus know the proper remedy to apply. This will give +him a command over his engine which should render him equal to any +emergency.</p> + +<p class="right"> +WALTER C. RUNCIMAN.<br /> +</p> +<p><span class="smcap">London, E.C.</span><br /> +<span class='pagenum'><a name="Page_6" id="Page_6">[Pg 6]</a></span></p> + + + +<hr /><p><span class='pagenum'><a name="Page_7" id="Page_7">[Pg 7]</a></span></p> +<h1>GAS AND OIL ENGINES<br /> + +<small>SIMPLY EXPLAINED</small></h1> + + + +<hr style="width: 15%;" /> +<h2><a name="CHAPTER_I" id="CHAPTER_I"></a>CHAPTER I</h2> + +<h3>INTRODUCTORY</h3> + + +<p class="noin"><span class="smcap">The</span> history of the gas engine goes back a long way, and the history of +the internal combustion engine proper further still. It will be +interesting to recount the main points in the history of the development +of the class of engine we shall deal with in the following pages, in +order to show what huge strides were made soon after the correct and +most workable theory had been formulated.</p> + +<p>In 1678 Abbé Hautefeuille explained how a machine could be constructed +to work with gunpowder as fuel. His arrangement was to explode the +gunpowder in a closed vessel provided with valves, and cool the products +of combustion, and so cause a partial vacuum to be formed. By the aid of +such a machine, water could be raised. This inventor, however, does not +seem to have carried out any experiments.</p> + +<p><span class='pagenum'><a name="Page_8" id="Page_8">[Pg 8]</a></span></p><p>In 1685 Huyghens designed another powder machine; and Papin, in 1688, +described a similar machine, which was provided with regular valves, as +devised by himself, in the <i>Proceedings of the Leipsic Academy</i>, 1688. +From this time until 1791, when John Barber took out a patent for the +production of force by the combustion of hydrocarbon in air, practically +no advancement was made. The latter patent, curiously enough, comprised +a very primitive form of rotary engine. Barber proposed to turn coal, +oil, or other combustible stuff into gas by means of external firing, +and then to mix the gases so produced with air in a vessel called the +exploder. This mixture was then ignited as it issued from the vessel, +and the ensuing flash caused a paddle-wheel to rotate. Mention is also +made that it was an object to inject a little water into the exploder, +in order to strengthen the force of the flash.</p> + +<p>Robert Street's patent of 1794 mentions a piston engine, in the cylinder +of which, coal tar, spirit, or turpentine was vaporised, the gases being +ignited by a light burning outside the cylinder. The piston in this +engine was thrown upwards, this in turn forcing a pump piston down which +did work in raising water. This was the first real gas engine, though it +was crude and very imperfectly arranged.</p> + +<p>In 1801 Franzose Lebon described a machine to be driven by means of +coal-gas. Two pumps were used to compress air and gas, and the mixture +was fired, as recommended by the inventor, by an electric spark, and +drove a piston in a double-working cylinder.</p> + +<p><span class='pagenum'><a name="Page_9" id="Page_9">[Pg 9]</a></span></p><p>The atmospheric engine of Samuel Brown, 1823, had a piston working in a +cylinder into which gas was introduced, and the latter, being ignited, +expanded the air in cylinder whilst burning like a flame. The fly-wheel +carried the piston up to the top of its stroke, then water was used to +cool the burnt gases, which also escaped through valves, the latter +closing when the piston had reached the top of its stroke. A partial +vacuum was formed, and the atmospheric pressure did work on the piston +on its down stroke. A number of cylinders were required in this engine, +three being shown in the specification all connected to the same +crank-shaft. According to the <i>Mechanic's Magazine</i>, such an engine with +a complete gas generating plant was fitted to a boat which ran as an +experiment upon the Thames.</p> + +<p>A two-cylinder engine working on to a beam was built in Paris, but no +useful results were obtained.</p> + +<p>Wright's engine of 1833 used a mixture of combustible gas and air, which +operated like steam in a steam engine. This engine had a water-jacket, +centrifugal governor, and flame ignition. In 1838 Barnett applied the +principle of compression to a single-acting engine. He also employed a +gas and air pump, which were placed respectively on either side of the +engine cylinder, communication being established between the receiver +into which the pumps delivered and the working cylinder as the charge +was fired. The double-acting engines which Barnett devised later were +not so successful.</p> + +<p>From this time to about 1860 very few practical<span class='pagenum'><a name="Page_10" id="Page_10">[Pg 10]</a></span> developments are +recorded. A number of French and English patents were taken out, +referring to hydrogen motors, but are not of much practical value.</p> + +<p>Lenoir's patent, dating from 24th January 1860, refers to a form of +engine which received considerable commercial support, and consequently +became very popular. A manufacturer, named Marinoni, built several of +these engines, which were set to work in Paris in a short time. Then, +due to sudden demand, the Lenoir Company was formed to undertake the +manufacture of these engines. It was claimed that a 4-horse-power engine +could be run at a cost of 3·4 shillings per day, or just one half the +cost of a steam engine using 9·9 pounds of coal per horse-power per +hour. Many similar exaggerated accounts of their economy in consumption +were circulated, and the public, on the strength of these figures, +bought.</p> + +<p>It was understood that 17·6 cubic ft. of gas were required per +horse-power per hour, but it was found that as much as 105 cubic ft. +were often consumed. The discrepancy between the stated figures and the +actual performance of the engine was a disappointment to the using +public, and, as a result, the Lenoir engine got a bad name.</p> + +<p>Hugon, director of the Parisian gas-works, who, together with Reithmann, +a watchmaker of Münich, hotly contested Lenoir's priority to this +invention, brought out a modification of this engine. He cooled the +cylinder by injecting water as well as using<span class='pagenum'><a name="Page_11" id="Page_11">[Pg 11]</a></span> a water-jacket, and used +flame instead of electric ignition. The consumption was now brought down +to 87·5 cubic ft.</p> + +<p>At the second Parisian International Exhibition, 1867, an atmospheric +engine, invented by Otto & Langen about this time, was shown. In this +engine a free piston was used in a vertical cylinder, the former being +thrown up by the force of the explosion. The only work done on the +up-stroke was that to overcome the weight of the piston and piston rod, +and the latter being made in the form of a rack, engaged with a toothed +wheel on the axle as the piston descended, causing the fly-wheel and +pulley to rotate.</p> + +<p>Barsanti and Matteucci were engaged in devising and experimenting with +an engine very similar to this some years before, but Otto & Langen, no +doubt, worked quite independently. Barsanti's engine never became a +commercial article; while Otto & Langen's firm, it is said, held their +own for ten years, and turned out about 4000 engines. In 1862 the French +engineer, Beau de Rochas, laid down the necessary conditions which must +prevail in order to obtain maximum efficiency. His patent says there are +four conditions for perfectly utilising the force of expansion of gas in +an engine.</p> + +<p>(1) Largest possible cylinder volume contained by a minimum of surface.</p> + +<p>(2) The highest possible speed of working.</p> + +<p>(3) Maximum expansion.</p> + +<p><span class='pagenum'><a name="Page_12" id="Page_12">[Pg 12]</a></span></p><p>(4) Maximum pressure at beginning of expansion.</p> + +<p>These are the conditions and principles, briefly stated, that combine to +form the now well-known cycle upon which most gas engines work at the +present time.</p> + +<p>It was not until 1876, fifteen years after these principles had been +enumerated, that Otto carried them into practical effect when he brought +out a new type of engine, with compression before ignition, higher +piston speed, more rapid expansion, and a general reduction of +dimensions for a given power. Due to this achievement, the cycle above +referred to has always been termed the "Otto" cycle.</p> + + + +<hr /><p><span class='pagenum'><a name="Page_13" id="Page_13">[Pg 13]</a></span></p> +<h2><a name="CHAPTER_II" id="CHAPTER_II"></a>CHAPTER II</h2> + +<h3>THE COMPONENT PARTS OF AN ENGINE</h3> + + +<p>Having recounted very briefly the chief points in the development of the +gas engine from its beginning, we may proceed to deal with matters of +perhaps more practical interest to those who we are assuming have had +little or no actual experience in making or working internal combustion +engines.</p> + +<p>The modern gas engine comprises comparatively few parts. Apart from the +two main castings—the bed and cylinder—a small engine, generally +speaking, consists of four fundamental members, viz., the valves and +their operating mechanism, the cams and levers; the ignition device for +firing the charge; and the governing mechanism for regulating the supply +and admission of the explosive charge. There are innumerable designs of +each one of these parts, and no two makes are precisely alike in detail, +as every maker employs his own method of achieving the same end, namely, +the production of an engine which comprises maximum efficiency with a +minimum of wear and tear and attention.</p> + +<p><span class='pagenum'><a name="Page_14" id="Page_14">[Pg 14]</a></span></p><p>Therefore, before dealing with each of these primary parts in an +arbitrary manner, and with the cycle of operations in detail, we propose +to make the reader familiar with the general arrangement and method of +working which usually obtains in the smaller power engines. In the +following illustrations these parts are shown. A (fig. 1) is the +ignition device which carries the ignition tube to fire the charge. H +and I (fig. 2) are the main valves, and GC (fig. 1.) is the gas-cock. +The side or cam shaft N (sometimes called the 2 to 1 shaft), the cams +which move the levers M, the latter in turn operating the valves, and +causing them to open and close at the proper time, are shown in fig. 11. +A bracket bolted up to the side of cylinder forms a bearing for one end +of the side shaft, and also carries a spindle at its lower end on which +the levers oscillate, transmitting the motion imparted to them by the +cams to the valves. The main cylinder casting and the bed need no +description. In some cases the bed is in two portions, though now a +great many makers are discarding the lower portion altogether, having +found that it is cheaper, and quite as satisfactory, to use a built-up +foundation instead, and, if necessary, to cut a trough for the fly-wheel +to run it. This arrangement, however, only obtains where larger engines +are concerned. A half-compression handle by which the exhaust cam is +moved laterally on the side shaft as required is not needed on very +small engines.</p> + +<p><span class='pagenum'><a name="Page_15" id="Page_15">[Pg 15]</a></span></p> + +<div class="figcenter" style="width: 500px;"> +<img src="images/image1.jpg" width="500" height="325" alt="Fig. 1." title="" /> +<span class="caption"><span class="smcap">Fig. 1.</span>—General Arrangement of a Gas Engine and +Accessories.</span> +</div> + +<p><span class='pagenum'><a name="Page_16" id="Page_16">[Pg 16]</a></span></p><p>Further reference will be made to this in another chapter, and, +although this is not a necessity on a <i>small</i> engine, it is always +employed on engines over 2 B.H.P. In fig. 1, HW is the cooling water +outlet and CW the inlet. A small drain cock is shown at DC, through +which the water in the cylinder water-jacket may be drawn off when +required. The pipes leading to the inlet and outlet of this supply are +connected to the cooling water tank by means of a couple of broad, flat +nuts and lead washers, one inside and the other outside the tank, the +latter, when clamped up well, making a perfectly water-tight joint. The +outlet pipe making an acute angle with the side of tank, the washers +used there should be wedge-shape in section. It is also desirable to fit +a stop-cock SC, so that the pipes can be disconnected from the engine +entirely, or the water-jacket emptied without running the whole of the +water out of the tank. The exhaust pipe EP is made up of gas-barrel. It +should lead from the engine to the silencer or exhaust box (if one is +found to be necessary) as directly as possible, <i>i.e.</i>, with no more +bends than are needed, and what there are should not be acute. The +silencer can be inside or outside the engine-room, whichever is most +convenient; but both it and the exhaust piping should be kept from all +direct contact with wood-work, and at the same time in a readily +accessible position.</p> + +<p>Beyond the exhaust-pipe and box and the water-tank, the gas bag GB and +gas meter (where small powers are concerned, the ordinary house or +workshop lighting meter may be used without inconvenience) are the only +other accessories which are included in a small installation.</p> + +<p><span class='pagenum'><a name="Page_17" id="Page_17">[Pg 17]</a></span></p> +<div class="figcenter" style="width: 500px;"> +<img src="images/image2.jpg" width="500" height="318" alt="Fig. 2." title="" /> +<span class="caption"><span class="smcap">Fig. 2.</span>—A Section of a Gas Engine.</span> +</div> + +<p><span class='pagenum'><a name="Page_18" id="Page_18">[Pg 18]</a></span></p><p>Fig. 2 gives a sectional view, showing the cylinder and liner. The +latter is a very desirable feature in any type of gas engine, but +especially in the larger sizes; for at any future time, should it be +found necessary to re-bore the liner, it can be removed with comparative +ease, and is, moreover, more readily dealt with in the lathe than the +whole cylinder casting would be.</p> + +<p>The liner is virtually a cast-iron tube, with a specially shaped flange +at either end. At the back end the joint between it and the cylinder +casting has to be very carefully made. This is a water <i>and</i> explosion +joint; hence it has not only to prevent water entering the cylinder from +the water-jacket, but also to be sufficiently strong to withstand the +pressure generated in the cylinder when the charge is fired. For this +purpose specially prepared coppered asbestos rings are used, which will +stand both water and intense heat. Sometimes a copper ring alone is +employed to make the joint. At the front end the liner is just a good +fit, and enters the bed easily, and a couple of bolts fitted in +corresponding lugs on the liner, pass through the back end of cylinder +casting, so that by tightening up these the joint at back end is made +secure. A small groove is cut on a flange, and a rubber ring, of about +<span class="above">1</span>⁄<span class="below">4</span>-in. sectional diameter, is inserted here when the liner is fitted +into the cylinder casting. This makes the water-jacket joint at the +front end.</p> + +<p><span class='pagenum'><a name="Page_19" id="Page_19">[Pg 19]</a></span></p> +<div class="figcenter" style="width: 450px;"> +<img src="images/image3.jpg" width="450" height="137" alt="Fig. 3." title="" /> +<span class="caption"><span class="smcap">Fig. 3.</span></span> +</div> + +<div class="figcenter" style="width: 350px;"> +<img src="images/image5.jpg" width="350" height="71" alt="Fig. 5." title="" /> +<span class="caption"><span class="smcap">Fig. 5.</span></span> +</div> + +<div class="figcenter" style="width: 450px;"> +<img src="images/image4.jpg" width="450" height="137" alt="Fig. 4." title="" /> +<span class="caption"><span class="smcap">Fig. 4.</span></span> +</div> + +<p><span class='pagenum'><a name="Page_20" id="Page_20">[Pg 20]</a></span></p><p>Lugs are provided on the bed and cylinder castings, and are bored to +receive steel bolts—three are sufficient, provided the metal in and +around these lugs is not pinched. In some cases a continuous flange is +provided on both bed and cylinder, and a number of bolts inserted all +the way round. This, however, is unnecessary, and has a somewhat clumsy +appearance. When these bolts are tightened up, the cylinder and liner +are clamped firmly to the bed; but the liner being free at the open end, +can expand longitudinally without causing stresses in the cylinder +casting.</p> + +<p>The combustion chamber K is virtually part of the cylinder, and has +approximately equal to one-fourth the total volume of the cylinder. The +shape varies somewhat in different makes of engines; in some it is +rectangular, with all the corners well rounded off; in others it is +practically a continuation of the cylinder, <i>i.e.</i>, it is circular in +cross-section, with the back end more or less spherical; while, again, +it is made slightly oval in cross-section; but in every case the corners +should be <i>well</i> curved and rounded off, so that there is no one part +which is liable to become heated disproportionately with the rest of the +casting; in fact, in the whole cylinder casting there should be no +sudden change, but a uniformity in the thickness of the metal employed. +This point should be carefully remembered, although it applies more +particularly to those parts of the casting subjected to higher +temperatures than the rest.</p> + +<p>The main bearings are usually of brass or <span class='pagenum'><a name="Page_21" id="Page_21">[Pg 21]</a></span>gun-metal, and are adjusted +for running in the same manner as any steam or other engines would be. +The "brasses" are in halves, and are held down by the cast-iron caps, as +shown in fig. 1.</p> + +<p>These bearings require extremely little attention, and do not show the +wear and tear of running nearly so soon as the connecting-rod brasses. +These, too, are usually of brass or gun-metal; but there are various +forms of construction employed in connection with the back end or piston +pin bearings. On very small engines the connecting rod is swollen at the +back end in the forging, and then machined up and drilled, as shown in +fig. 3. In this hole the brasses are inserted after being scraped up to +a good fit on the piston pin.</p> + +<p>A flat is cut on one of the brasses, and a set screw is fitted, as +shown, to prevent any movement of the latter after the final adjustment +has been made. A lock nut should be used in conjunction with this set +screw. Another method, and one more generally used on larger engines, is +shown in fig. 4. In this case the brasses are larger than in the former, +where they are virtually a split bush; here they have holes drilled in +them to take the bolts, the latter usually and preferably being turned +up to the shape shown in fig. 5.</p> + + + +<hr /><p><span class='pagenum'><a name="Page_22" id="Page_22">[Pg 22]</a></span></p> +<h2><a name="CHAPTER_III" id="CHAPTER_III"></a>CHAPTER III</h2> + +<h3>HOW A GAS ENGINE WORKS</h3> + + +<p>The gas engine of the present day, although from a structural point of +view is very different to the early engine, or even that of fifteen +years ago, is, in respect to the principle upon which it works, very +similar. The greater number of smaller power engines in use in this +country work on what is known as the Otto or four-cycle principle; and +it is with this class of engine we propose to deal.</p> + +<p>Reference to the various diagrams in the text will help considerably, +and make it an easy matter for any reader hitherto totally unacquainted +with such engines to see why and how they work.</p> + +<p>Coal-gas consists primarily of five other gases, mixed together in +certain proportions, these proportions varying slightly in different +parts of the country:—Hydrogen (H), 50; marsh gas (CH<sub>4</sub>), 38; +carbon-monoxide, 4; olefines (C<sub>6</sub>H<sub>4</sub>), 4; nitrogen (N), 4.</p> + +<p>Gas <i>alone</i> is not explosive; and before any practical use can be made +of it, a considerable quantity of<span class='pagenum'><a name="Page_23" id="Page_23">[Pg 23]</a></span> air has to be added, diluting it down +to approximately ten parts air to one of pure gas. This mixture is <i>now</i> +highly explosive.</p> + +<p>The reader will do well to bear these facts constantly in mind, +especially when he is repairing, adjusting, or experimenting with a gas +engine. We wish to emphasise this at the outset, because a consideration +of these facts will keep cropping up throughout all our dealings with +the gas engine, and if once a fairly clear conception is obtained of how +gas will behave under certain and various conditions, half, or even more +than half, our "troubles" will disappear; the cry that the gas engine +has "gone wrong" will be heard less often, and users would soon learn +that the gas engine is in reality as worthy of their confidence as any +other form of power generator in common use.</p> + +<p>But to revert to the explanation of the cycle of operations. The cycle +is completed in four strokes of the piston, <i>i.e.</i>, two revolutions of +the crank shaft.</p> + +<p>At the commencement of the first out-stroke (the charging or suction +stroke) gas and air are admitted to the cylinder through the respective +valves (fig. 6), and continue to be drawn in by what may be termed the +sucking action of the piston, until the completion of this stroke (the +<i>precise</i> position of the closing and opening of the valves will be +referred to later on). The next stroke (fig. 7) is the compression +stroke. All the valves are closed whilst the piston moves inwards, +compressing the gases, until at the end of this stroke, and at the +instant of maximum <span class='pagenum'><a name="Page_24" id="Page_24">[Pg 24]</a></span>compression, the highly explosive charge is fired by +means of the hot tube or an electric spark, as the case may be. The +ensuing stroke—the second out-stroke of the cycle—is the result of the +explosion, the expanding gases driving the piston rapidly before them; +this, then, is the expansion, or working stroke (fig. 8.)</p> + +<div class="figcenter" style="width: 450px;"> +<img src="images/image6.jpg" width="450" height="160" alt="Fig. 6." title="" /> +<span class="caption"><span class="smcap">Fig. 6.</span>—Commencement of first out-stroke suction or +charging stroke. Gas and air valve about to open.</span> +</div> + +<div class="figright" style="width: 450px;"> +<img src="images/image7.jpg" width="450" height="160" alt="Fig. 7." title="" /> +<span class="caption"><span class="smcap">Fig. 7.</span>—Compression stroke, during which all valves +remain closed.</span> +</div> + +<p>During the last—the second inward—stroke (fig. 9) the exhaust valve is +opened, and the returning piston sweeps all the burnt gases (the product +of combustion) out into the exhaust pipe and so into the atmosphere. +This completes the cycle, and the piston, crank, and valves are in the +same relative positions as formerly, and the same series of operations +is repeated again and again. Of course, it is not always the case that +both air <i>and</i> gas valve are opened on the charging stroke; that depends +upon<span class='pagenum'><a name="Page_25" id="Page_25">[Pg 25]</a></span> the method employed to govern the speed of the engine. Supposing +it were governed on the hit and miss principle (to be explained +hereafter), the gas valve would be allowed to remain closed during the +charging stroke, and air alone would be drawn into the cylinder, then +compressed, but not being explosive would simply expand again on the +working stroke, giving back nearly all the energy which was absorbed in +compressing it, and finally be exhausted in the same manner as the burnt +gases are.</p> + +<div class="figleft" style="width: 450px;"> +<img src="images/image8.jpg" width="450" height="153" alt="Fig. 8." title="" /> +<span class="caption"><span class="smcap">Fig. 8.</span>—Second out stroke, showing position of valves +during working stroke.</span> +</div> + +<div class="figright" style="width: 450px;"> +<img src="images/image9.jpg" width="450" height="153" alt="Fig. 9." title="" /> +<span class="caption"><span class="smcap">Fig. 9.</span>—Second inward stroke, showing position of valves +during the exhaust stroke.</span> +</div> + +<div class="figcenter" style="width: 450px;"> +<img src="images/image10.jpg" width="450" height="153" alt="Fig. 10." title="" /> +<span class="caption"><span class="smcap">Fig. 10.</span>—First out-stroke, showing position of valves +during the charging stroke.</span> +</div> + +<p><span class='pagenum'><a name="Page_26" id="Page_26">[Pg 26]</a></span></p><p>Fig. 10 shows diagrammatically the position of crank, piston, and +valves <i>during</i> the charging stroke.</p> + +<div class="figcenter" style="width: 500px;"> +<img src="images/image11.jpg" width="500" height="668" alt="Fig. 11." title="" /> +<span class="caption"><span class="smcap">Fig. 11.</span>—Cross Section of Cylinder.</span> +</div> + +<p>In figs. 1 and 2 we gave drawings of two gas engines, which are typical +examples of modern practice. Huge strides have been made in recent years +in gas-engine work, as regards both workmanship and efficiency, so that +to-day we have in the gas engine a machine whose mechanical efficiency +compares favourably with that of any other power generator, and whose +thermal efficiency is very much greater.</p> + +<p><span class='pagenum'><a name="Page_27" id="Page_27">[Pg 27]</a></span></p> +<div class="figcenter" style="width: 500px;"> +<img src="images/image12.jpg" width="500" height="552" alt="Fig. 12." title="" /> +<span class="caption"><span class="smcap">Fig. 12.</span>—Longitudinal Section of Cylinder.</span> +</div> + +<p><span class='pagenum'><a name="Page_28" id="Page_28">[Pg 28]</a></span></p><p>Figs. 11 and 12 show respectively a sectional end and side elevation of +the cylinder, from which it will not be difficult for the reader, +however unacquainted he may be with gas-engine work, to see how the +various requirements and peculiarities of the engine should be +considered and provided for.</p> + +<p>A most important desideratum in any machine or engine is that it shall +be as simple in construction as ever possible; complicated mechanism +should only be introduced when such addition or complication compensates +adequately for what must necessarily be a higher first cost, and +incidentally the greater wear and tear and attention involved. Figs. 11 +and 12 show what has been done to simplify the construction of the gas +engine in recent years. The main feature in this case is the very +get-at-able position of the two main valves—the air valve F and the +exhaust E. These valves, as may be seen from the drawing, are capable of +withdrawal after the cover of the combustion chamber has been removed. +The latter is an iron casting, shaped and faced up to make an absolutely +tight joint; no asbestos or any packing is used to make this joint—and +is held in place by four studs, as shown. Thus, all that is necessary is +to remove the four nuts, lift the cover off, then pull out the pins +which keep the spiral springs in position, and withdraw the valves. The +latter are seated direct on to the metal of the cylinder casting, the<span class='pagenum'><a name="Page_29" id="Page_29">[Pg 29]</a></span> +gun-metal bushes A and B acting as guides. Further reference to A (the +mixer), which serves a twofold purpose, will be made later on.</p> + +<p>The gas valve and cock are mounted in a separate casting, which is +carried by a couple of studs, the joint between this and cylinder being +made with a piece of rubber insertion. The gas enters at the gas-cock, +passes through the valve and port G, and round the annular space in the +bush or "mixer" A, previously mentioned, and thence through a number of +small holes in same, immediately below the seat of the air valve F. At +the same time, pure air is drawn in <i>via</i> the air box (as explained +hereafter), through port L (fig. 11), and thence up the centre of bush A +and over the small holes through which the gas is flowing. The two then +thoroughly mix and enter the combustion chamber together as the air +valve F is opened. This device produces a perfectly homogeneous mixture, +which conduces in no small measure to perfect combustion when the +explosion takes place, and upon which, to a very great extent, depends +the efficiency of the engine. Besides possible loss in this direction, +however, there is another source of waste which cannot be eliminated, +and that is the heat taken away by the cooling water which surrounds the +cylinder. As this loss is inevitable, the best thing we can do is to +make it as small as possible. Theoretically, it would be no small +advantage if we could work at very much higher temperatures than we do +at the present time, and it is only certain mechanical difficulties +which bar the way and so effectually<span class='pagenum'><a name="Page_30" id="Page_30">[Pg 30]</a></span> prevent the already high thermal +efficiency of the engine being greatly increased.</p> + +<p>It is no easy matter to overcome these difficulties completely, but +improvements in this direction are continually being made, so that +troubles which attended the gas-engine user years ago no longer exist.</p> + +<p>All that we require of the cooling water is that it shall keep certain +working parts of the engine at a reasonable temperature; for instance, +the cylinder must not be so hot as to deprive the lubricating oil of its +property to lubricate, neither must the exhaust valve become so hot as +to cause it to seize in the bush and stick up; but, beyond such +considerations as these, the higher the temperature is at the +commencement of each explosion the more efficient will the engine be. +The object, then, is to do as little cooling as possible, and to apply +the cooling effect at the right parts; hence the passages and chambers +through which the cooling water circulates should be so arranged that +those which require to be kept at a low temperature are in close +proximity to the cooling water. On some of the engines of days gone by, +the exhaust valve was carried in a large iron casting, this in turn +being bolted to the cylinder casting and communicating with the +combustion chamber by means of a port. Such an arrangement was found to +be not only clumsy but inefficient; the water passages were small and +difficult to get at; they readily furred up; and moreover, the joint +between this casting and the cylinder was<span class='pagenum'><a name="Page_31" id="Page_31">[Pg 31]</a></span> necessarily a water <i>and</i> +explosion joint, and the fewer we have of these the better.</p> + +<p>The method—if it may be called a method—of overcoming or preventing +the exhaust valve becoming too hot is, in the case of figs. 11 and 12, +simply one of judicious arrangement and design. The cooling water enters +by the inlet K (fig. 11), and circulates round the exhaust valve port X +and valve E immediately, before becoming heated, thus keeping the +hottest of the working parts of the engine at a suitable temperature; +and the valve seat, being in direct metallic communication with the cold +water, does not become burnt or pitted. On the other side of the exhaust +valve we have the air valve and its passages, through which cool air is +continually being drawn; this also helps to keep the exhaust valve cool.</p> + +<p>From this, then, we may conclude that overheating of the cylinder will +not occur under normal conditions, given an engine of good design; but, +if this trouble does arise, we may safely look first of all for some +defect in the cooling water circulation. Some waters contain a greater +amount of impurities than others, and consequently the water space may +furr up more rapidly in one district than in another. But this deposit, +even under the worst conditions, accumulates very slowly, and the +operation of cleaning out the water-jacket is a very infrequent +necessity. The exhaust valve, however, may become overheated if it is +allowed to get into bad condition, <i>i.e.</i>, leaky. Its seat should be +well looked after, or<span class='pagenum'><a name="Page_32" id="Page_32">[Pg 32]</a></span> the hot gases will blow past when it is +presumably shut; and if this defect, slight though it may be to begin +with, is allowed to develop, both the seat, the valve head, and the +spindle will become burnt away and pitted, perhaps badly, due to the +excessive heat.</p> + + + +<hr /><p><span class='pagenum'><a name="Page_33" id="Page_33">[Pg 33]</a></span></p> +<h2><a name="CHAPTER_IV" id="CHAPTER_IV"></a>CHAPTER IV</h2> + +<h3>IGNITION DEVICES</h3> + + +<p>The ignition devices commonly employed may be divided into three main +classes—the metal tube, the porcelain tube, and the electric ignition. +These again may be subdivided: The first being either iron or nickel +(hecknum as they are sometimes called); the second are of two +kinds—single-ended and double-ended; and the third takes many forms +which many of my readers are possibly well acquainted with, such as the +magneto, the induction coil and trembler, and the high-tension magneto +ignition, the latter device having been used successfully on various +occasions, though not yet universally adopted.</p> + +<p>The first-named have one or two advantages over the nickel tube. They +are very inexpensive, and are easily heated to the required temperature; +moreover, they can be made at home, should occasion demand. On the other +hand, they are not so durable, have a very uncertain life, and +consequently need renewing frequently—their average life being<span class='pagenum'><a name="Page_34" id="Page_34">[Pg 34]</a></span> not +more than 60 working hours. Fig. 13 gives an outline drawing of an iron +tube, with its burner and chimney fixed in position. The tube is very +similar to a piece of <span class="above">1</span>⁄<span class="below">4</span>-in. gas-barrel, closed up at one end and a +taper thread (<span class="above">1</span>⁄<span class="below">4</span>-in. gas) cut on the other; in fact, gas-barrel may be +used for making these tubes at home—and measure about 7 or 8 in. over +all It is screwed into a firing block, which in turn is screwed into the +combustion chamber end, so that when right home it is in such position +that the tube stands quite vertical. The section of the tube, fig. 13, +shows the condition it gets into after having been in use some time. The +bore, it will be seen, has become almost completely closed up, so that +there is practically no communication between the hot part of the tube +and the combustion chamber. This closing up of the bore is very gradual, +and<span class='pagenum'><a name="Page_35" id="Page_35">[Pg 35]</a></span> it is in the early stages of this process that erratic firing is +likely to occur; sometimes the charge will be successfully fired and +sometimes not. It may be as well to mention here that the length of the +tube, although to a certain extent immaterial, should neither be +excessively long nor abnormally short, the precise length varying with +the size of the engine. A <span class="above">1</span>⁄<span class="below">4</span>-in. tube, 8 ins. long, may be used +successfully on engines ranging from <span class="above">1</span>⁄<span class="below">2</span> to 6 horse-power, provided a +suitable burner is fitted enabling the tube to be heated at any required +spot. After the first charge has been fired, and the exhaust takes +place, practically all the burnt gases are cleared out of the cylinder, +but a small amount of these will generally remain in the tube and the +bore of the<span class='pagenum'><a name="Page_36" id="Page_36">[Pg 36]</a></span> firing block. On the ensuing compression stroke these inert +gases are compressed to the far end of the tube, thus making way for the +explosive mixture to reach the hot portion, and explode, thus sending a +jet of flame into the main volume of the mixture which is immediately +ignited. Hence there is no advantage in having a tube too long, while, +on the other hand, it <i>must</i> not be too short.</p> + +<div class="figleft" style="width: 300px;"> +<img src="images/image13.jpg" width="300" height="594" alt="Fig. 13." title="" /> +<span class="caption"><span class="smcap">Fig. 13.</span></span> +</div> + +<div class="figright" style="width: 250px;"> +<img src="images/image14.jpg" width="250" height="254" alt="Fig. 14." title="" /> +<span class="caption"><span class="smcap">Fig. 14.</span></span> +</div> + +<div class="figcenter" style="width: 450px;"> +<img src="images/image15.jpg" width="450" height="337" alt="Fig. 15." title="" /> +<span class="caption"><span class="smcap">Fig. 15.</span></span> +</div> + +<p>The asbestos lining, shown in fig. 13, may be of various thicknesses, +according to the size of the chimney and the tube; the reason for this +will be apparent to many; but being a most important factor in the +heating of the tube, and consequently the working of the engine, it will +be advisable to deal with this point more fully.</p> + +<p>Due mainly to the peculiar behaviour of iron tubes under heat and +internal pressure, it is always advisable to look to them first of all +when the engine shows signs of missing fire; and to always examine the +bore of a fresh one, and ascertain that it is perfectly clear before +putting it in. The adjustment of the ignition tube, although one of the +most important and necessary to be made on the whole engine, is in +itself a perfectly simple matter. It must be understood that the +ignition tube cannot, with the ordinary means at our disposal, be kept +at too high a temperature; but it must not be assumed that either the +<i>size</i> of the flame, or the <i>time</i> the flame has been alight, is +conclusive evidence that the tube is, or ought to be, sufficiently hot +to fire the charge successfully. It is an uncommon<span class='pagenum'><a name="Page_37" id="Page_37">[Pg 37]</a></span> thing to hear a man +exclaim—after it has been pointed out that his tube is practically +cold—"Why, it's been alight for hours!"</p> + +<p>If such is the case with you, reader, you may very rightly assume that +the burner is not properly adjusted, and so does not give the <i>right +kind of flame</i>.</p> + +<p>In order to get the hottest possible flame, the quantity of gas and air +must be mixed in the right proportions. A common fault is that there is +too much gas allowed to flow through the nipple, compared with the +amount of air being drawn in at the air aperture, fig. 13. The result +is, we get a flame of great length, but one which is not at all suited +to our requirements; and instead of giving up its heat to the tube and +the asbestos lining of the chimney, a large amount of gas we are +presumably burning <i>in</i> the chimney is not being burnt there at all, +for, on applying a light just above the chimney top, a quantity of this +gas we are wasting will be seen to burn with a flickering blue flame.</p> + +<p>To put matters right, it is necessary to do one of two things—either +cut down the supply of gas or increase the air-supply. Providing the air +aperture is normal, <i>i.e.</i>, the same size as it was originally, it is +better to adjust the <i>gas</i>, which may be done by tapping up the nipple +N, as indicated in the enlarged sketch, fig. 14, until just the right +amount of gas can flow.</p> + +<p>As a rule, if there is too much air, the flame will burn with a loud +roaring noise, and is liable to fire back. The nipple should then be +opened out with<span class='pagenum'><a name="Page_38" id="Page_38">[Pg 38]</a></span> a small reamer—the tang of a small file, ground to a +long taper point, makes an admirable tool for this purpose. Whether the +burner is of the ordinary bunsen type, or the ring or stove type, the +above remarks apply, as in every case the flow of gas is governed by the +size of the orifice through which it flows.</p> + +<p>There is no need to use anything beyond a touch of oil when putting in a +new tube, in order to make a perfectly tight joint; white or red lead +are quite unnecessary, and are liable to make it a troublesome matter to +remove the tube on future occasions. Neither should undue force be +applied when putting in new tubes; it is liable to wear the thread in +the firing block, which results in a partial stoppage of the ignition +hole, as indicated in fig. 15. This is especially the case if we happen +to get hold of a tube with its screwed part slightly smaller than usual.</p> + +<p>The asbestos with which the chimney is lined should be about <span class="above">1</span>⁄<span class="below">8</span> in. +thick, and, when renewing, the same thickness should be used as +originally. A thicker board will reduce the annular space round the +tube, and will have a choking effect on the flame—much the same as +referred to above, when there is too much gas and not enough air. A +simple method of lining the chimney is to cut a block of wood to the +inside dimensions of the chimney, less <span class="above">1</span>⁄<span class="below">4</span> in. in width and thickness, +then soften the asbestos cardboard by immersing in water, and bend it +round the wood, cutting off to the required size, <i>i.e.</i>, till the two +edges form a neat butt joint. It can be allowed<span class='pagenum'><a name="Page_39" id="Page_39">[Pg 39]</a></span> to remain on the mould +until dry—when it will retain its shape—or can be put into the chimney +straight away, if it is wanted for use immediately. In the latter case, +however, it will be some fifteen minutes or so before the tube will +attain its working temperature. Asbestos linings gradually become worn +and ragged, and small flakes are apt to detach themselves and fall down +into the burner, which, of course, prevents the flame playing as it +should around the tube. In such cases it is not always necessary to fit +a new lining; if the chimney is removed, the loose flakes shaken out and +the asbestos well damped and patted down with a wooden or steel +foot-rule or other suitably shaped tool, it will be fit for another long +spell of work.</p> + +<p>The nickel or hecknum tubes are treated in the same manner as the iron, +but, as we mentioned before, are more durable, but require more heating +to get them up to a workable temperature. Their greater first cost is +compensated to some extent by makers in some cases guaranteeing them for +six months.</p> + +<p>Of the porcelain ignition devices, we will deal with the double-ended +tube first, it being the more commonly used of the two in this country. +This form of tube is usually about 3 in. long, <span class="above">1</span>⁄<span class="below">2</span> in. diameter, and +open at both ends. It may be mounted in a metal casting, in form not +unlike the small gas stoves for heating soldering irons. It is heated +the greater part of its length by a couple of rows of gas jets, and is +frequently surrounded by<span class='pagenum'><a name="Page_40" id="Page_40">[Pg 40]</a></span> an asbestos lining. The whole arrangement is +in reality a tiny furnace. When in position for working, one end of the +tube is open to the ignition passage leading and communicating with the +combustion chamber, while the other end is sealed, through butting up +against a metal cap or plate. An asbestos washer is interposed between +the tube at each end and the metal it bears against, thus making a more +or less flexible joint. A thumb screw is arranged at the outside end of +the tube, by means of which pressure can be applied to clamp it up +between the washers to the desired extent. Some care has to be exercised +in adjusting this form of tube for running. When heated to the working +temperature it, of course, expands, so that, if tightened up too much +when cold, it is under a fairly high compression; and when the engine is +started, and the explosion takes place, it not infrequently bursts, if +there is not sufficient "give" in the washers to allow for the +expansion. On the other hand, if not clamped up sufficiently tight to +start with, when the explosion occurs, the washer at one or each end is +blown out. This adjustment has to be made to a nicety, and, although a +somewhat difficult matter, success may be attained after one or two +trials. It is advisable, after a new tube has been put in, to start up +the engine gently, <i>i.e.</i>, with less than the normal supply of gas, and +increase to the full amount gradually whilst running. This may be done +by simply opening the gas-cock on engine partially in the first place.</p> + +<p><span class='pagenum'><a name="Page_41" id="Page_41">[Pg 41]</a></span></p><p>The single-ended porcelain tube is not so well known here as on the +continent; why, we cannot say; certainly it is preferable in every way. +We give a few illustrations, showing the method of using this tube.</p> + +<p>Figs. 16 and 17 show the general arrangement of tube and chimney and the +manner in which they are fixed to the cylinder. The device consists +primarily of three parts—the body or chimney B, the cover C, and the +tube itself T. The body is a light iron casting, carried by a couple of +studs SS, which are either screwed into the firing block F, or direct +into the metal of the cylinder casting if no firing-block is used; the +latter may very well be dispensed with in the smaller-sized engines.</p> + +<p>The tube is made of thin porcelain, slightly bell-mouthed at its open +end, and is mounted in a thick metal washer W, as shown in fig. 18 in +section, the joint being made with a little asbestos paper, moistened.</p> + +<p>The block F and the face of the body B (fig. 16) are recessed to take +the washer W easily, but the depth of both recesses taken together must +be about <span class="above">1</span>⁄<span class="below">16</span> in. less than the thickness of the washer W; thus, when +the tube is placed in position between the body B and the block F, and +the former screwed up by means of the two nuts, as shown in the figure +16, the effect is to clamp the <i>washer</i> which carries the tube, but <i>not +the porcelain tube itself</i>.</p> + +<p><span class='pagenum'><a name="Page_42" id="Page_42">[Pg 42]</a></span></p> + +<div class="figleft" style="width: 400px;"> +<img src="images/image16.jpg" width="400" height="580" alt="Fig. 16." title="" /> +<span class="caption"><span class="smcap">Fig. 16.</span></span> +</div> + +<div class="figright" style="width: 400px;"> +<img src="images/image17.jpg" width="400" height="681" alt="Fig. 17." title="" /> +<span class="caption"><span class="smcap">Fig. 17.</span></span> +</div> + +<div class="figcenter" style="width: 350px;"> +<img src="images/image18.jpg" width="350" height="774" alt="Fig. 18." title="" /> +<span class="caption"><span class="smcap">Fig. 18.</span></span> +</div> + +<p><span class='pagenum'><a name="Page_43" id="Page_43">[Pg 43]</a></span></p><p>The latter is left perfectly free to expand; and yet, owing to its +particular shape, the pressure in the cylinder during the compression +and explosion stroke only tends to make the joint between the tube and +washer more secure. The action of this ignition device depends upon the +tube heater H, which is merely a small bunsen burner, the flame of which +impinges on the tube at one particular spot, raising it to a very high +temperature—almost white heat. Most of my readers will know the +formation of the bunsen flame. It in composed of two distinct zones. The +inner one, marked A in fig. 18, is a perfectly cold part of the flame, +and appears to be a pale-blue coloured cone.</p> + +<p>It is the outer zone which is the hot portion of the flame, hence this +part <i>only</i> must be allowed to play on the tube. The tip of the blue +cone A must be kept about <span class="above">1</span>⁄<span class="below">4</span> in. below the tube, in order to ensure the +hottest part of the flame impinging precisely where the heat is +required.</p> + +<p>The total length of the whole flame is, to a certain extent, immaterial; +but, generally speaking, it should be adjusted so that the length of the +inner cone A is about 1 in. or 1-<span class="above">1</span>⁄<span class="below">4</span> in. The same methods which we +described in the early part of this chapter can be employed in the +adjustment of this burner, but some care should be exercised to get the +correct flame length.</p> + +<p>The result of allowing the cold part of the flame to impinge on the tube +is observable in fig. 18. The black spot indicated on the drawing +actually appears as a black or sooty spot when looking at the tube under +these conditions; but in reality no discoloration whatever takes place, +the spot <span class='pagenum'><a name="Page_44" id="Page_44">[Pg 44]</a></span>disappearing immediately the cone A is made shorter, or the +burner H lowered in the chimney B, so that the tip of A is just below, +and does not touch the tube at all.</p> + +<p>The adjustment of the length of cone A may be accomplished in two +ways—(1) by keeping the supply of gas constant, and varying the amount +of air admitted at aperture K, fig. 18; (2) by keeping the supply of air +constant, and varying the amount of gas admitted through nipple N. The +first method is to be preferred when it is necessary to make any slight +adjustment due to the variation of gas pressure during the day, and may +be accomplished by fitting a small sliding shield G, as shown in the +figs. 16 and 17, and moving it round so that it covers, more or less, +the aperture K. Thus the length of cone A may be adjusted to a nicety in +a very few seconds. This shield keeps all draughts and puffs of wind +from the fly-wheel away from the aperture, and helps the flame to burn +very steadily. In the first place, of course, the flame will be +regulated by opening out or tapping up the nipple N (an enlarged sketch +of which is given in fig. 14), so that cone A is just about 1-<span class="above">1</span>⁄<span class="below">4</span> in. +long when air aperture is full open; but once this is done, any future +adjustment can be made by throttling the air-supply, or raising or +lowering the burner bodily, the set screw keeping it in any desired +position (see fig. 17).</p> + +<p>From the foregoing remarks it will be seen that the most noteworthy +features of this form of ignition<span class='pagenum'><a name="Page_45" id="Page_45">[Pg 45]</a></span> are the ease and certainty with which +the tube can be fixed in a few moments; that when the two nuts on the +studs SS have been tightened up there is no likelihood of the joints +being "blown," for, as we said before, only the metal washer is clamped +up, the porcelain tube itself being as free to expand as it was before. +It is also at once obvious when any adjustment of the flame is +necessary; there need be no uncertainty as to whether the tube is hot +enough or not.</p> + + + +<hr /><p><span class='pagenum'><a name="Page_46" id="Page_46">[Pg 46]</a></span></p> +<h2><a name="CHAPTER_V" id="CHAPTER_V"></a>CHAPTER V</h2> + +<h3>MAGNETO IGNITION</h3> + + +<p>The third form of ignition we have to deal with is the electric.</p> + +<p>There are a great number of different types made and used, but for +gas-engine use perhaps that known as the magneto ignition is the most +satisfactory. With this form, neither accumulators, dry batteries, or +spark coils are required, and consequently a greater simplicity is +arrived at than would otherwise be the case.</p> + +<p>In fig. 19 we show diagrammatically the ordinary form of magneto +machine. Virtually it is a small dynamo which is fixed to the side of +cylinder casting, and is operated in the manner shortly to be described. +As we do not propose to enter into more than a brief explanation of why +and how this apparatus generates current to produce the required spark, +perhaps a simple analogy will make matters most intelligible to any +reader not well acquainted with electrical phenomena. We know that when +a current of electricity is flowing in a wire, and the wire be<span class='pagenum'><a name="Page_47" id="Page_47">[Pg 47]</a></span> suddenly +broken, a spark will occur at the point of breakage. This fact may be +observed in an ordinary electric bell when ringing; at the tip of the +contact breaker a number of tiny sparks may be seen to occur, due to the +rapid make and break of the current flowing in the circuit. Precisely +the same action takes place in our magneto-igniter, but, instead of a +multitude of tiny sparks, we produce one at a time, at definite +intervals, viz., at the commencement of each explosion stroke.</p> + +<div class="figcenter" style="width: 450px;"> +<img src="images/image19.jpg" width="450" height="305" alt="Fig. 19." title="" /> +<span class="caption"><span class="smcap">Fig. 19.</span></span> +</div> + +<p>In the later form of magneto machines there is a soft iron sleeve +between the magnet poles and the armature. The former is connected to a +system of levers by which a reciprocating motion is imparted to it by +means of a suitably arranged cam on the side shaft. It has been found +that better results are obtained by causing the magnetic field to move<span class='pagenum'><a name="Page_48" id="Page_48">[Pg 48]</a></span> +relative to the armature winding than to move the latter through a +stationary field. Reference to the diagrams, figs. 20 and 21, will make +this clear.</p> + +<p>In fig. 19 the cam C is shown just on the point of allowing the lever L +to fly back into its normal position, due to the action of the springs +comprising a dashpot S. As the cam rotates, it pushes the lever L to the +left, the sleeve (or virtually the armature A) is also rotated through a +portion of a revolution comparatively slowly; but as soon as L is +released, the sleeve (or armature) flies back again almost +instantaneously and for the moment is generating a current in the same +manner as would any ordinary continuous current dynamo.</p> + +<div class="figcenter" style="width: 400px;"> +<img src="images/image20.jpg" width="400" height="632" alt="Fig. 20." title="" /> +<span class="caption"><span class="smcap">Fig. 20.</span></span> +</div> + +<div class="figcenter" style="width: 400px;"> +<img src="images/image21.jpg" width="400" height="632" alt="Fig. 21." title="" /> +<span class="caption"><span class="smcap">Fig. 21.</span></span> +</div> + +<p><span class='pagenum'><a name="Page_49" id="Page_49">[Pg 49]</a></span></p><p>At the instant the maximum current is being generated, the circuit is +broken by means of the contact breaker D, fig. 19, which we show in +detail in fig. 22. The latter is mounted on the end of the combustion +chamber, and consists of two parts, D and P.</p> + +<div class="figcenter" style="width: 400px;"> +<img src="images/image22.jpg" width="400" height="618" alt="Fig. 22." title="" /> +<span class="caption"><span class="smcap">Fig. 22.</span></span> +</div> + +<p>D is an easy fit in the hole bored to receive it, and has a mushroom +valve head and seating, as shown, so that it moves readily when struck +by the projection E on the rod R (fig. 19); but yet, acting in the +manner of a non-return valve, it allows no gas to<span class='pagenum'><a name="Page_50" id="Page_50">[Pg 50]</a></span> escape when the +explosion takes place in the cylinder. D is therefore in direct metallic +communication with the engine frame and earth.</p> + +<p>P is a fixed metal pin, carefully insulated from all contact with the +engine frame and earth. To this pin one end of the armature winding is +connected, whilst the other end is connected to the engine frame.</p> + +<p>Thus a closed circuit is formed, and when the current is generated it +flows from one terminal of magneto through wire to pin P, on to D, +through D to earth (<i>i.e.</i>, engine frame), and so back to other terminal +on magneto.</p> + +<p>And as the circuit is broken between D and P, we obtain a spark, as +previously explained, which may be timed to take place by adjusting the +position of cam C on side shaft relatively to the position of piston.</p> + +<p>It may be said that the position of the magneto-igniter is immaterial; +it will be fixed in different positions on different types of engines, +and so long as the operating mechanism is simple and effective, <i>i.e.</i>, +as direct as is practicable, it works well, and requires little +attention. The timing of the spark will be dealt with in the chapter on +Cams and Valve Settings.</p> + + + +<hr /><p><span class='pagenum'><a name="Page_51" id="Page_51">[Pg 51]</a></span></p> +<h2><a name="CHAPTER_VI" id="CHAPTER_VI"></a>CHAPTER VI</h2> + +<h3>GOVERNING</h3> + + +<p>The devices for governing the speed of the engine may be divided, +broadly speaking, into two classes—the inertia or hit and miss +governor, and the centrifugal. Of the latter type we will give an +instance first. In figs. 23 and 24 the governor gear is shown +diagrammatically, consisting of a couple of weights WW suspended from a +vertical spindle. These fly apart when caused to revolve by the bevel +wheel gearing BB, and raise the sleeve S to a greater or lesser extent. +A recess in the latter engages a lever arm L, through which the vertical +movement of the sleeve S is converted into a horizontal movement of the +sleeve T. The latter is carried by the valve lever P, and is virtually a +roller which engages with one or other of the steps of the cam C, +according to the speed of the engine. The object of this arrangement is +to keep the ratio of air to gas uniform throughout all variations of +load. The gas and air valve are shown as both being operated by the same +lever P, the accurate timing of the latter being obtained by means of +set screws.</p> + +<p><span class='pagenum'><a name="Page_52" id="Page_52">[Pg 52]</a></span></p> +<div class="figcenter" style="width: 450px;"> +<img src="images/image23.jpg" width="450" height="723" alt="Fig. 23." title="" /> +<span class="caption"><span class="smcap">Fig. 23.</span></span> +</div> + +<p><span class='pagenum'><a name="Page_53" id="Page_53">[Pg 53]</a></span></p> +<div class="figcenter" style="width: 450px;"> +<img src="images/image24.jpg" width="450" height="711" alt="Fig. 24." title="" /> +<span class="caption"><span class="smcap">Fig. 24.</span></span> +</div> + +<p><span class='pagenum'><a name="Page_54" id="Page_54">[Pg 54]</a></span></p><p>Messrs Dougill & Co.'s engines are fitted with a step down cam and +governor such as this. The centrifugal governor is often arranged so +that instead of the charge being merely reduced in volume, the whole +charge is cut out, and no explosion whatever takes place. (In this +respect the same results are obtained as when a hit and miss governor is +used, and the latter form therefore is to be preferred, especially on +small engines, where the difference between the indicated power and the +brake power is always, even under the best conditions, fairly great.)</p> + +<p>In this case the governor lever only operates the gas valve; the air +valve being opened on every charging or suction stroke, whether gas is +admitted or not.</p> + +<p>Another application of the centrifugal governor is to suspend a distance +piece on the end of the governor lever, so that at normal speed this +distance piece is interposed between the gas valve spindle and the lever +operating it. In that case the gas valve will be opened. But if the +speed is above the normal, the distance piece will be raised clear of +the valve spindle, and the opening mechanism (driven by a cam on the +side shaft) will simply move forward and recede again without ever +touching the gas valve.</p> + +<p>There are any number of movements which have been, and there are many +more which could be, devised to give the same result; and it depends +principally upon the form of engine in question which device we adopt.</p> + +<p>The simplest and most direct action is, however,<span class='pagenum'><a name="Page_55" id="Page_55">[Pg 55]</a></span> always the best; +complicated mechanism is to be deprecated, especially on small engines. +For this reason is the inertia governor more generally fitted to such +engines.</p> + +<div class="figcenter" style="width: 400px;"> +<img src="images/image25.jpg" width="400" height="851" alt="Fig. 25." title="" /> +<span class="caption"><span class="smcap">Fig. 25.</span></span> +</div> + +<p>A simple form of this governor is shown in fig. 25. The gas valve V is +shown on its seating. It is screwed into a pecker block B, and pinned as +shown. The latter should be of cast steel, tempered to a straw colour; +or if mild steel or iron is used, it must be well case-hardened, in +order to resist wear. The pecker P (also tempered hard) is mounted on +the cast-iron weight W, which in turn is pivoted on the valve lever L. +It will be seen that the weight W (which is only held in the position +shown by the spring S) will tend to lag behind when a sudden upward +motion is imparted to the lever L.<span class='pagenum'><a name="Page_56" id="Page_56">[Pg 56]</a></span> Thus it depends upon the degree of +suddenness with which L moves whether the pecker P remains in the same +relative position to the lever as the latter travels upwards and engages +with the pecker block B, or whether it misses it and simply slides over +the face of the block. The adjustment of the spring S is effected by +screwing up or slacking out the milled nuts T; and on the degree to +which this spring is compressed depends the sensitiveness of the +governor, and consequently the speed of the engine. To obtain accurate +and steady governing with this type of mechanism it is essential that +the weight be perfectly free on its spindle, and that nothing but the +spring S holds, or tends to hold, it in the position shown. On this +account it is advisable to provide a "lip" on the pecker block, as +shown, to keep the area of contact as small as possible. This +effectually prevents any sticking, should a superfluity of oil happen to +get on either block or pecker. For similar reasons there should be some +clearance between A and the pecker, <i>i.e.</i>, the latter should only bear +at one point and not bed flat against A.</p> + +<p>Another form of inertia governor is shown in fig. 26 of the hit and miss +type, which is employed by Messrs Capel & Co. on many of their engines.</p> + +<p>It consists of three main parts—the brass arm L carried on a stud D, on +which it is free to move; the weight W, which carries the pecker P +pivoted at the upper end of L; and the pecker block B, which engages the +pecker when the engine requires a charge of gas.</p> + +<p><span class='pagenum'><a name="Page_57" id="Page_57">[Pg 57]</a></span></p><p>The governing action is dependent upon the shape of the operating cam +from X to Y. (In the case already dealt with, the lever L serves to +operate both air and gas valves, and so one cam only is necessary; but +in this instance the gas valve is operated by a separate cam, and a +greater nicety of adjustment is obtainable.)</p> + +<div class="figright" style="width: 450px;"> +<img src="images/image26.jpg" width="450" height="356" alt="Fig. 26." title="" /> +<span class="caption"><span class="smcap">Fig. 26.</span></span> +</div> + +<p>If the speed of the engine is sufficiently high, the arm L is thrust +forward at such a rate that the weight W tends to lag behind, with the +result that P is raised above the notch in B, as shown by the dotted +lines in drawing. On the other hand, when the speed is too low, the arm +L will not be thrust forward with so great a degree of suddenness, the<span class='pagenum'><a name="Page_58" id="Page_58">[Pg 58]</a></span> +weight W will have time to move with L, and the relative position of W +and P to L will remain the same. Hence, in the first case, when a +<i>further</i> forward movement is given to L by the cam, the pecker P is +clear of B, and omits to open the gas valve V; in the second case, P +engages with B, and the gas valve is held open during the time the +portion of cam Y to Z is passing over the roller R on arm L.</p> + +<p>The great drawback to some forms of governors is not that they fail to +govern well when new, but that no provision is made to ensure them +working steadily when a bit worn. The shape of the cam has everything to +do with the regular working of this form of governor.</p> + +<p>Supposing our cam was of the shape shown in fig. 27, <i>i.e.</i>, the +governing and opening portion all in one curve, it would cause the +pecker to move both <i>forward</i> and in an <i>upward</i> direction at the <i>same +time</i>, so that at the moment of engaging B, P might still be moving in +an upward direction, which would cause uncertainty of action, especially +if the tips of the engaging members were at all blunt through wear; and, +in all probability, P would fly off B after partially opening the gas +valve.</p> + +<p>This behaviour is very undesirable, as the small quantity of gas so +admitted to the cylinder is quite useless, and a sheer waste is +incurred. With the governing arrangement shown in fig. 26, this trouble +does not exist. The cam is so designed that the first rise from X to A +determines whether or not the valve is to be opened; the curve from A to +Y is<span class='pagenum'><a name="Page_59" id="Page_59">[Pg 59]</a></span> struck from the centre of the side shaft; thus, during that +portion of the revolution the arm L is stationary, and the pecker at the +same instant takes up a definite position either in the notch in B or on +top of it, and is ready to open the valve if the speed of the engine is +such as to require an explosion, or simply to slide over the top of B, +allowing the valve to remain closed. It is most interesting to observe +the action of this governor; when an engine fitted with one is running +very slowly, the three distinct movements of the pecker P may be clearly +discerned as the respective portions of the cam pass over the small +roller R.</p> + +<div class="figcenter" style="width: 350px;"> +<img src="images/image27.jpg" width="350" height="352" alt="Fig. 27." title="" /> +<span class="caption"><span class="smcap">Fig. 27.</span></span> +</div> + + + +<hr /><p><span class='pagenum'><a name="Page_60" id="Page_60">[Pg 60]</a></span></p> +<h2><a name="CHAPTER_VII" id="CHAPTER_VII"></a>CHAPTER VII</h2> + +<h3>CAMS AND VALVE SETTINGS</h3> + + +<p>With the gas, as with any other kind of engine, the valve settings are +of primary importance. On very small engines it is often the case that +only the exhaust valve is operated mechanically.</p> + +<p>Again, there are several well-known makes which operate the gas and +exhaust mechanically while the air valve is opened by suction alone. +Though opinions differ as to which is the best course to take, there can +be little doubt that, with all three valves mechanically operated, a +greater nicety of adjustment is obtainable than would be otherwise +possible. And provided the working parts are neatly made and finished, +they will take but little power to drive them; and such loss would be +compensated by the additional power and efficiency obtained from the +engine, due to satisfactory and correct adjustment.</p> + +<p>In fig. 28 we give a diagram showing the exact positions of the crank +when the gas, air, and exhaust valves open and close respectively, under +normal conditions of working. The solid circle represents<span class='pagenum'><a name="Page_61" id="Page_61">[Pg 61]</a></span> the first +revolution of the crank shaft, starting from the commencement of the +suction stroke, and the dotted circle the second revolution, during +which the explosion and exhaust strokes take place; the dotted +horizontal line shows the position of crank at the back and front dead +centres.</p> + +<p>As a clear conception of why certain things happen under certain +conditions is most desirable, we will first describe the operation of +marking off the cams which operate the respective valve levers, and then +discuss the effect of various "settings" of the valves on the running of +the engine.</p> + +<div class="figleft" style="width: 400px;"> +<img src="images/image28.jpg" width="400" height="280" alt="Fig. 28." title="" /> +<span class="caption"><span class="smcap">Fig. 28.</span></span> +</div> + +<p>Assuming that we are still dealing with the Otto cycle engine, the cam +or side shaft will revolve at precisely half the speed of the crank +shaft. This 2 to 1 motion is obtained by means of toothed<span class='pagenum'><a name="Page_62" id="Page_62">[Pg 62]</a></span> wheels, or a +screw gear. In the former case, where plain or bevel cog-wheels are +employed, the one fixed on the crank shaft must be exactly half the +diameter of the one on the side shaft, <i>i.e.</i>, it must have one half the +number of teeth. On the other hand, if a screw gear is used, the +relative diameters of the two wheels may vary, but the pitch of the +teeth on the one must be twice that of the other. These wheels sometimes +have the teeth or thread formed in the casting, and sometimes they are +cut after a plain casting has been made. The latter kind are, needless +to say, better than the former, which often require filing up in order +to make every tooth alike, and ensure sweet running.</p> + +<p>We know already in what positions our crank has to be at the opening and +closing of the three valves, and with the aid of the diagram, fig. 28, +we can determine the size of the cams. In fig. 29, S is the side shaft +to which the cams have to be keyed, R the roller on valve lever, the +latter being represented by the centre lines LL, as all we require to +find is the motion this lever will transmit to the valve, the spindle of +which is shown at V.</p> + +<p>Fig. 30 shows diagrammatically the position of crank at the opening and +closing of the air valve. From this we see that the angle through which +the crank travels during the time the air valve is open is equal to the +obtuse angle ABC. Now, as the side shaft S revolves at half the speed of +crank, it is obvious that the former will travel through only half that +angle in the same space of time, <i>i.e.</i>,<span class='pagenum'><a name="Page_63" id="Page_63">[Pg 63]</a></span> through an angle equal to ABD. +We can now transfer this angle on to S, fig. 29, and draw two lines SE, +SF, cutting a circle GHJ, representing the back of the cam, which latter +passes in front of the roller R without causing any movement of the +lever L.</p> + +<div class="figcenter" style="width: 450px;"> +<img src="images/image29.jpg" width="450" height="477" alt="Fig. 29." title="" /> +<span class="caption"><span class="smcap">Fig. 29.</span></span> +</div> + +<p><span class='pagenum'><a name="Page_64" id="Page_64">[Pg 64]</a></span></p> + +<div class="figleft" style="width: 300px;"> +<img src="images/image30.jpg" width="300" height="292" alt="Fig. 30." title="" /> +<span class="caption"><span class="smcap">Fig. 30.</span></span> +</div> + +<div class="figcenter" style="width: 500px;"> +<img src="images/image31.jpg" width="500" height="506" alt="Fig. 31." title="" /> +<span class="caption"><span class="smcap">Fig. 31.</span></span> +</div> + +<p>It will be seen that by drawing a line forming a tangent to the circle +GHJ at F and another at E, and producing these, they will meet at point +K. Consequently, as the side shaft rotates in the direction indicated, +the lever L will <i>begin</i> to open the valve V when the cam is in the +position shown in fig. 29, reach a maximum opening at K, and finally +close when the cam has moved so that point E is now where F was. With a +cam of this shape, however, a considerable portion of the stroke would +have passed before the valve was raised any <i>appreciable</i><span class='pagenum'><a name="Page_65" id="Page_65">[Pg 65]</a></span> distance off +its seat; it would only be fully open for an instant, viz., when K was +passing over R, and would begin to close again directly.</p> + +<p>Moreover, if the engine were running at even a slow speed, the motion +imparted to lever L would be indefinite; and this, especially if the +governor is fitted to the air valve lever, as in fig. 25, is very +undesirable. Therefore, to obtain a definite opening we must set out the +cam, as shown in fig. 31. In this diagram the roller is shown standing +clear of the back of cam by about <span class="above">1</span>⁄<span class="below">16</span> in. A line MN is then drawn, +forming a tangent to both roller R and circle GHJ at points F and O +respectively. This gives us the opening portion of cam. Then from the +centre S with radius SF describe the arc FE (shown dotted in fig. 31), +and set off the angle required (ABD, fig. 30), as previously explained. +Through point E draw a line forming a tangent to circle GHJ, and produce +it towards P. This line gives us the closing portion of cam. The +distance W is of course variable, according to the amount of lift we +give the valve. By comparing these two diagrams it will be seen that in +both cases the valve will be opened the same length of time, but in +first case the motion will be indefinite and uncertain. In practice the +corners are rounded off somewhat, in order to obtain a steady motion; +and when the air cam is also the governing cam, it is advisable to round +off the opening face, as indicated in fig. 32. Upon the shape of this +face both the sensitiveness and the life of the governor gear depends. +If it<span class='pagenum'><a name="Page_66" id="Page_66">[Pg 66]</a></span> is nicely rounded off, giving a gradual rise, very little tension +(or compression, as the case may be) of the controlling spring will be +necessary to give the required speed to engine; whereas, if the rise is +sudden, the spring will have to be screwed up tighter, and, if uneven +and lumpy (<i>i.e.</i>, not a fair curve), the result will, of course, be +erratic governing.</p> + +<div class="figcenter" style="width: 450px;"> +<img src="images/image32.jpg" width="450" height="484" alt="Fig. 32." title="" /> +<span class="caption"><span class="smcap">Fig. 32.</span></span> +</div> + +<p>A certain amount of clearance should always be provided between the +roller and the back of cam<span class='pagenum'><a name="Page_67" id="Page_67">[Pg 67]</a></span> (compare figs. 29 and 31), that is, the +roller should not bear against the cam, except during that portion of +the stroke in which it is actually operating the valve, viz., from F to +E (fig. 31). A small stop interposed between the lever and some +convenient part of the engine, such as the side-shaft bracket bearing, +answers this purpose.</p> + +<div class="figleft" style="width: 300px;"> +<img src="images/image33.jpg" width="300" height="336" alt="Fig. 33." title="" /> +<span class="caption"><span class="smcap">Fig. 33.</span></span> +</div> + +<div class="figcenter" style="width: 450px;"> +<img src="images/image34.jpg" width="450" height="364" alt="Fig. 34." title="" /> +<span class="caption"><span class="smcap">Fig. 34.</span></span> +</div> + +<p>The size and shape of the exhaust cam is found in the same manner as +above described; the angle through which it operates is greater than +that of the air cam, and is shown in fig. 33. A fair margin should be +allowed for filing or machining these castings up; the shape and sizes +arrived at by the above described method being finished measurements.<span class='pagenum'><a name="Page_68" id="Page_68">[Pg 68]</a></span> +Fig. 34 gives the outline of an exhaust cam worked out from the setting +diagram, fig. 33.</p> + +<div class="figleft" style="width: 400px;"> +<img src="images/image35.jpg" width="400" height="109" alt="Fig. 35." title="" /> +<span class="caption"><span class="smcap">Fig. 35.</span></span> +</div> + +<div class="figright" style="width: 400px;"> +<img src="images/image37.jpg" width="400" height="109" alt="Fig. 37." title="" /> +<span class="caption"><span class="smcap">Fig. 37.</span></span> +</div> + +<div class="figleft" style="width: 400px;"> +<img src="images/image41.jpg" width="400" height="109" alt="Fig. 41." title="" /> +<span class="caption"><span class="smcap">Fig. 41.</span></span> +</div> + +<div class="figcenter" style="width: 400px;"> +<img src="images/image42.jpg" width="400" height="109" alt="Fig. 42." title="" /> +<span class="caption"><span class="smcap">Fig. 42.</span></span> +</div> + +<p>We may now consider the relative positions these two cams will occupy +when keyed up on the side shaft. Assuming that we have both cams +finished to the proper shape and size, and the keyway cut in the side +shaft, we can commence to mark off the position of keyway in the air +cam. With the crank in the position shown in fig. 35, the air cam is<span class='pagenum'><a name="Page_69" id="Page_69">[Pg 69]</a></span> +slipped on to the side shaft and brought to the position shown in fig. +32. The keyway being already cut in the side shaft, the position for +that in the cam may be scribed off, as shown by dotted lines (fig. 32), +the cam removed, and the keyway cut. It is as well, however, to check +this mark by turning the crank round to position shown in fig. 37, +<i>i.e.</i>, the closing of air valve. The side shaft will also turn through +exactly half this angle, so that when the cam is again slipped on the +latter, the scriber marks and keyway in shaft should be exactly in line, +as they were in fig. 32, and the fall of the cam—the closing +portion—should just be touching roller R, but not sufficient to keep +the valve open (see fig. 38). The slightest movement of the crank from +this point in a forward direction should result in a little play<span class='pagenum'><a name="Page_70" id="Page_70">[Pg 70]</a></span> being +felt in the lever L, assuming that the cam is also moved just enough to +keep the scriber marks in line with the existing keyway.</p> + +<div class="figcenter" style="width: 450px;"> +<img src="images/image36.jpg" width="450" height="328" alt="Fig. 36." title="" /> +<span class="caption"><span class="smcap">Fig. 36.</span></span> +</div> + +<div class="figcenter" style="width: 400px;"> +<img src="images/image38.jpg" width="400" height="435" alt="Fig. 38." title="" /> +<span class="caption"><span class="smcap">Fig. 38.</span></span> +</div> + +<div class="figcenter" style="width: 400px;"> +<img src="images/image39.jpg" width="400" height="435" alt="Fig. 39." title="" /> +<span class="caption"><span class="smcap">Fig. 39.</span></span> +</div> + +<p>By these operations it will be at once evident whether the cam is too +large or too small. Supposing it is too small, we will obtain two sets +of marks indicating the position of keyway, as shown in fig. 39, and it +is obvious that we must give the lever less play by screwing up the set +screws shown in fig. 11. The effect of this is to cause the valve to +open earlier and close later than it would if the play were greater; as +it would were the operating portion of cam larger. A minimum amount of +play must always be allowed, however. When two sets of marks are +obtained, the mean must be taken and the keyway cut as shown by the +thick lines in fig.<span class='pagenum'><a name="Page_71" id="Page_71">[Pg 71]</a></span> 39. The exhaust cam in larger engines is usually +made with a swelling on the opening portion, as shown in fig. 40, so +that the valve is <i>very slightly</i> opened some time before the crank has +reached the position shown in fig. 41. Fig. 42 shows position of crank +at the close of exhaust valve, and the two last-mentioned diagrams +correspond with the two positions in which the exhaust cam is shown in +fig. 34. The small lump on the back of exhaust cam, fig. 40, is only +required on engines above 3 B.H.P. to relieve the compression on the +compression stroke when starting up. By moving the roller R on valve +lever longitudinally, so that it engages both parts of cam as they pass +in front of it, the exhaust valve is held open during a small portion of +the compression stroke, usually closing when the crank has reached the +bottom centre.</p> + +<p>Referring again to fig. 26, this gas or governor cam may be set out, and +the keyway marked on the same principle as already described for the air +and exhaust valves. An end view of the three cams keyed up on the side +shaft is given in fig. 40<span class="smcap">A</span>. In small engines it is convenient to have +the air and exhaust cams made in one casting, when one key only will be +required. On some engines, instead of employing a movable roller or +valve lever, the exhaust cam is fitted on side shaft with a +"feather"—<i>i.e.</i>, a headless key—and the cam being capable of +longitudinal movement, such movement being controlled by a small lever +or handle, called the half-compression lever.</p> + +<p><span class='pagenum'><a name="Page_72" id="Page_72">[Pg 72]</a></span></p> + +<div class="figleft" style="width: 300px;"> +<img src="images/image40.jpg" width="300" height="264" alt="Fig. 40" title="" /> +<span class="caption"><span class="smcap">Fig. 40</span></span> +</div> + +<div class="figright" style="width: 450px;"> +<img src="images/image40a.jpg" width="450" height="392" alt="Fig. 40a" title="" /> +<span class="caption"><span class="smcap">Fig. 40a</span></span> +</div> + +<p>Having once thoroughly grasped the important part the cams play in the +working of the engine, it will be an easy matter to adjust the valve +settings, and to keep them adjusted correctly. The effect of a wrong +setting will then be strikingly apparent. On small engines a separate +cam to operate the gas valve is not a necessity; and the practice of +fitting<span class='pagenum'><a name="Page_73" id="Page_73">[Pg 73]</a></span> the gas valve spindle (or the pecker, the effect would be the +same) with a device for increasing or diminishing its length, is also +unnecessary and unsound.</p> + +<p>The wear on a well-designed gas valve operating mechanism is practically +nil; and even if there was wear, the effect would be to cause the valve +to open a trifle later and close sooner than it would otherwise, <i>i.e.</i>, +it would remain open a shorter time during each charging stroke. This in +turn (other conditions remaining the same) would give us a weaker +mixture; and although too weak a mixture is preferable to a too rich +one, we should have to adopt some means of increasing the richness of +the mixture; otherwise the maximum power of the engine would soon be +seen to diminish.</p> + +<p>To get the mixture normal again we must either enlarge the gas inlet or +cut down the air-supply somewhat, and so keep the proportions the same. +That is to say, the quality of the mixture is dependent upon the +relative dimension of the gas and air inlets. We know by actual trial +that if at the completion of the charging stroke the pressure in the +cylinder is approximately that of the atmosphere, better results are +obtained than when the pressure is considerably below that of the +atmosphere. Thus, the larger we make the inlet ports (but still +retaining correct relative dimensions) the more readily will the mixture +be drawn into the cylinder as the piston moves forward, tending to +create a vacuum. Of the two courses open to us to retain a good mixture +it is preferable to open out the gas-supply, for by cutting<span class='pagenum'><a name="Page_74" id="Page_74">[Pg 74]</a></span> down the +air-supply, and sucking the gas in, due to the partial vacuum being +formed, we should be keeping the proportions correct at the expense of +reducing the total volume of the explosive mixture (more strictly +speaking, the density of the charge) admitted to the cylinder.</p> + +<p>Under normal conditions it is not necessary to create a high vacuum to +suck the gas into the cylinder, but it is as well to understand what +results we would tend to produce, did we work on these lines. Of course, +with small high-speed engines fitted with suction air valve, the vacuum +is higher than it would be in slow-speed engines with mechanically +operated valves. If we take an extreme case as an example, where, to get +any gas to speak of into the cylinder the air-supply would have to be +cut down or throttled to an abnormal extent, we will realise at once +that such a small quantity of both air and gas would have been drawn in, +and consequently the mixture would be so rarefied that on the +compression stroke the pressure would possibly be extremely low and +totally inadequate to produce efficient working. Moreover, working at +such a high vacuum as this would not only prevent us obtaining a normal +explosion in the cylinder, but would upset the working of the exhaust +valve. The latter being held down on its seat during the suction stroke +by means of a spiral spring would be lifted off its seat by suction (the +partial vacuum in the cylinder), and any burnt gases which happened to +be hanging about in the exhaust port or pipe would be drawn into the<span class='pagenum'><a name="Page_75" id="Page_75">[Pg 75]</a></span> +cylinder again, and tend to damp the ensuing explosion. Too early +closing of the exhaust should be avoided almost as rigorously as too +late. The latter will affect the working in a similar way to the exhaust +being lifted on the charging stroke by suction; on the other hand, if it +closes too soon, the entire volume of burnt gases will not have been +swept out of the cylinder, and the effect will again be to damp the +following explosion.</p> + +<p>The gas valve opens just after the crank is above the back centre and +closes just before the front centre is reached, that is, opening a +little after the air valve and closing a shade before it, thus every +particle of gas is used in the cylinder, due to a draught of air being +drawn in after the gas valve has been closed.</p> + +<p>The settings of the valve being of primary importance, no matter what +size engine we are dealing with, and being also the most confusing +matter for anyone unacquainted with gas engines to grasp, it will not be +out of place to suggest a simple method of checking these settings.</p> + +<p>Let us begin by pulling the fly-wheel round backwards until we feel the +piston is on the compression stroke, then from this point—the crank +being about 45° above the front centre—pull the wheel round until the +crank is in the position for the exhaust opening (see fig. 28). In this +position there should be but the <i>slightest</i> play in the exhaust lever, +showing that the valve is <i>just</i> on point of opening; and by keeping +one's hand on the lever whilst the fly-wheel<span class='pagenum'><a name="Page_76" id="Page_76">[Pg 76]</a></span> is pulled round <i>very +slowly</i> (it is a good plan to get some one else to do the pulling +round), it is possible to ascertain the precise point at which the valve +opens. Next pull round till the crank is in the position for the air +valve opening, and observe that it is set correctly. Then go on to a +trifle above the back centre, where the exhaust valve should close, and +so on till the opening and closing of each valve has been checked. It +will be noticed that the air, and sometimes the gas, valve opens before +the exhaust closes. This overlap is necessary; and it will be found that +the smaller the engine and the higher the speed the greater this overlap +will be to obtain good results, although a good deal of individual +judgment must be used in settling the exact amount of overlap, as the +requisite amount may, to get the best results, vary in different engines +of precisely the same dimensions and type.</p> + +<p>When dealing with engines which have no separate gas valve—the gas +being admitted with the air, which is sometimes the case with very small +engines—the above notes referring to the gas setting independently, +will, of course, not hold good.</p> + +<p>It may be mentioned with regard to the lump on the opening side of the +exhaust cam, that this if overdone is found to be detrimental on large +engines, and even on small ones. If it is too large, it will cause both +exhaust valve and seat to become burnt and pitted, due to the surface +being exposed to the exceedingly high temperature of the expanding +gases. If it is too large, it is equivalent to opening the exhaust valve +too early, and the effect is the same, viz., a waste of power and damage +to the valve and its seat.</p> + +<p><span class='pagenum'><a name="Page_77" id="Page_77">[Pg 77]</a></span></p> +<div class="figcenter" style="width: 350px;"> +<img src="images/image43.jpg" width="350" height="651" alt="Fig. 43." title="" /> +<span class="caption"><span class="smcap">Fig. 43.</span></span> +</div> + +<p><span class='pagenum'><a name="Page_78" id="Page_78">[Pg 78]</a></span></p> +<div class="figcenter" style="width: 450px;"> +<img src="images/image44.jpg" width="450" height="231" alt="Fig. 44.—Brake Testing." title="" /> +<span class="caption"><span class="smcap">Fig. 44.</span>—Brake Testing.</span> +</div> + +<p>The method of grinding in the valves to their seats with emery powder +and oil is so well known that no further description is needed here. We +give, however, in fig. 43 a sketch showing a very expeditious way of +dealing with very badly worn or burnt seats. The sketch explains itself. +Such a tool is readily made; even the cutter could be turned and filed +up to shape and then hardened at home. By lightly tapping in the taper +cotter pin little by little, sufficient pressure is put on the cutter to +make it an easy matter to completely re-face an old seat or form a new +one. A T-wrench or "tommy" can be used to work the cutter spindle. The +lower part of the latter must be the same diameter as the existing valve +spindle; the bush acts as a guide; and as the bevel of the cutter<span class='pagenum'><a name="Page_79" id="Page_79">[Pg 79]</a></span> +should be the same as that of the valve, a very little grinding in with +emery powder is required to finish the job off.</p> + +<p>In fig. 44 we give a diagram showing the method of testing for Brake +H.P. of engine, as it is frequently interesting to make such a simple +test after any alterations or adjustments have been made.</p> + +<p>Two spring balances and a rope or cord (according to the size of the +engine), fitted with a few wood blocks as shown in section, fig. 44, to +keep the rope on the rim of fly-wheel, is all that is required for this +test. The following formula may be used for arriving at the B.H.P.:—</p> + +<p class="center"> +B.H.P. = (S<sub>1</sub> − S<sub>2</sub>) 3·14 × D x R / 33000<br /> +<br /></p> +<p>S<sub>1</sub> = Reading in lbs. of spring balance No. 1.</p> +<p>S<sub>2</sub> = Reading in lbs. of spring balance No. 2.</p> +<p>D = Diameter of fly-wheel and diameter of brake rope in feet.</p> +<p>R = Revolutions of fly-wheel per minute.</p> + +<p>As 3·14 × D / 33000 will always remain the same for any given engine and +gear, we may call that expression C; then the B.H.P. may be written—</p> + +<p class="center"> +B.H.P. = (S<sub>1</sub> − S<sub>2</sub>) C R.<br /> +</p> + + + +<hr /><p><span class='pagenum'><a name="Page_80" id="Page_80">[Pg 80]</a></span></p> +<h2><a name="CHAPTER_VIII" id="CHAPTER_VIII"></a>CHAPTER VIII</h2> + +<h3>OIL ENGINES</h3> + + +<p>The small oil engine is practically the same as the gas engine, with the +addition of a vaporiser for converting the oil into gas, or vapour, to +be exploded in the cylinder; consequently the one may be converted into +the other in many cases without much trouble. The difficulty of +producing an efficient oil engine lies principally in devising a +satisfactory and reliable vapouriser—one which will work equally well +under all loads. The heat supplied to the chamber must be sufficient to +vaporise the oil, but not great enough to decompose it. There are +various methods of vaporising the oil, and many types of vaporisers are +employed to attain the same end. There are some in which a charge of oil +is drawn by suction into a hot chamber in which it is converted into +vapour and at the same time mixed with a small quantity of hot air; this +rich mixture is then passed into the combustion chamber of the engine, +in the same manner as coal-gas would be, where it is further diluted +with more<span class='pagenum'><a name="Page_81" id="Page_81">[Pg 81]</a></span> air drawn in through the air valve. Other arrangements cause +a jet of oil to be injected into a chamber containing hot air, in the +form of spray, which immediately converts the oil into vapour, and is +then passed into the cylinder, compressed, and fired. Then, again, we +can pump oil through a spraying nipple into the vapouriser (which is +kept at a suitable temperature) whilst the cylinder is being filled with +air on the suction stroke. On the following compression stroke the air +is driven into the vapouriser, which communicates with the cylinder +through a narrow neck, and mixes intimately with the oil vapour. +Gradually, as the pressure rises, due to compression, the charge becomes +more and more explosive, until at the completion of this stroke it has +attained the proper proportions of air and oil vapour, and is fired by +the temperature of the vapouriser and that caused by a high compression; +that is, the charge is fired automatically; and once the engine is +running, no heating lamp is required to keep the vapouriser at the +correct temperature. It is necessary, however, to raise it to the +workable temperature at starting. This is known as the Hornsby-Akroyd +method.</p> + +<p>Capel's arrangement is also simple and efficient, and has the additional +advantage of being capable of being fitted to their existing gas +engines, the conversion being made in a very short time. This vapouriser +consists primarily of a tubular casting A, on the outside of which are +formed a series of vertical ribs, shown in plan, fig. 46, running<span class='pagenum'><a name="Page_82" id="Page_82">[Pg 82]</a></span> to +within a short distance of the flange at one end, as shown in the +section, fig. 45, thus providing an annular space C between the upper +ends of the ribs and the flange. This casting is enclosed by an outer<span class='pagenum'><a name="Page_83" id="Page_83">[Pg 83]</a></span> +casing B, which fits well over the inner tube. It has also a number of +small holes drilled near the lower end communicating with the channels +between the ribs. Thus it will be seen that when the gas valve is opened +and suction takes place, air is drawn in through these holes, passes up +into the annular space C below the top flange, from there travels to the +opposite side of vapouriser, and mixes with the oil which is also being +drawn in through a small nipper at N, fig. 45. Both then pass between a +series of pegs, where they become thoroughly mixed, and finally pass on +to the inlet valve V, fig. 47, and so into the cylinder, where the +complete charge is mixed up and compressed and fired in the usual +manner. Iron ignition tubes may be used, and one heating lamp serves a +double purpose in keeping the tube and vapouriser hot at the same time. +This lamp is fed by means of a pump actuated from the side shaft. The +plunger of the pump is loaded with a spiral spring, which may be +adjusted to give any desired pressure, and is kept constant and steady +by means of an air vessel. This pump is shown in fig. 48. It is actuated +by means of a rod and lever from the side shaft of engine. The plunger P +works in a barrel B, which is carried by a small reservoir R, the latter +being in communication with the main oil tank by means of the pipe H.</p> + +<div class="figleft" style="width: 300px;"> +<img src="images/image46.jpg" width="300" height="276" alt="Fig. 46." title="" /> +<span class="caption"><span class="smcap">Fig. 46.</span></span> +</div> + +<div class="figright" style="width: 450px;"> +<img src="images/image45.jpg" width="450" height="537" alt="Fig. 45." title="" /> +<span class="caption"><span class="smcap">Fig. 45.</span></span> +</div> + +<p><span class='pagenum'><a name="Page_84" id="Page_84">[Pg 84]</a></span></p> +<div class="figleft" style="width: 350px;"> +<img src="images/image47.jpg" width="350" height="749" alt="Fig. 47." title="" /> +<span class="caption"><span class="smcap">Fig. 47.</span></span> +</div> + +<p><span class='pagenum'><a name="Page_85" id="Page_85">[Pg 85]</a></span></p> +<div class="figright" style="width: 350px;"> +<img src="images/image48.jpg" width="350" height="392" alt="Fig. 48." title="" /> +<span class="caption"><span class="smcap">Fig. 48.</span></span> +</div> + +<div class="figleft" style="width: 400px;"> +<img src="images/image49.jpg" width="400" height="653" alt="Fig. 49." title="" /> +<span class="caption"><span class="smcap">Fig. 49.</span></span> +</div> + +<p><span class='pagenum'><a name="Page_86" id="Page_86">[Pg 86]</a></span></p> +<div class="figright" style="width: 350px;"> +<img src="images/image50.jpg" width="350" height="464" alt="Fig. 50." title="" /> +<span class="caption"><span class="smcap">Fig. 50.</span></span> +</div> + +<div class="figcenter" style="width: 450px;"> +<img src="images/image51.jpg" width="450" height="497" alt="Fig 51." title="" /> +<span class="caption"><span class="smcap">Fig. 51.</span></span> +</div> + +<p>The plunger is loaded with a spiral spring, and has a ball valve, as +shown. Intermediate between this small reservoir and the main oil tank +is another set of valves, shown in fig. 49. It will be seen that the +suction of the pump will draw the oil up, the small and lower ball +valve, of course, allowing it to pass freely. On the down stroke the +lower valve will be automatically closed, and the oil will be put under +pressure, this being determined by the load on the plunger valve, which +is adjustable by means of the screw S, fig. 48. When the required +pressure in<span class='pagenum'><a name="Page_87" id="Page_87">[Pg 87]</a></span> the pipe P, figs. 45 and 49, has been attained, the plunger +valve lifts on each stroke and the surplus oil flows through the plunger +into the small reservoir R. The latter is at about the same level as +another still smaller reservoir M (shown in figs. 47 and 50), a flow of +oil being established between the two by means of a pipe Q (see figs. 48 +and 50). In the reservoir R is fitted an overflow pipe, so that the oil +cannot rise beyond a certain level; hence the head of oil in the smaller +one M is always constant. On the suction stroke a partial vacuum is +formed in the engine cylinder, consequently the pressure in the +vapouriser drops somewhat below that of the atmosphere,<span class='pagenum'><a name="Page_88" id="Page_88">[Pg 88]</a></span> and this small +difference in pressure is enough to cause the oil to rise in the small +passage X, fig. 45, beyond its normal level, and overflow into the +vapourising chamber, as previously described. The valve or nipper N is +shown open in the diagram, fig. 45, and all that is required to stop the +engine when running is to drop the small handle L, fig. 45, when the +valve will close, due to the spring S. The air vessel shown in fig. 49 +is in communication with the pipe leading to the blow lamp. A pressure +gauge can also be fitted, although it is not in any way a necessity.</p> + +<p>The ratchet wheel and pawl shown in fig. 48 are part of the lubricator. +The wheel drives a brass or gun-metal plug, producing an intermittent +rotary motion. The plug has a small hole in its periphery, which becomes +filled with oil when it is at the upper part of its travel, and empties +the oil out into a discharge pipe T, when it is inverted, and is then +led away and applied to the piston at the required spot. Fig. 51 shows +this arrangement in section.</p> + + + + + + + + +<pre> + + + + + +End of the Project Gutenberg EBook of Gas and Oil Engines, Simply Explained, by +Walter C. Runciman + +*** END OF THIS PROJECT GUTENBERG EBOOK GAS AND OIL ENGINES *** + +***** This file should be named 27286-h.htm or 27286-h.zip ***** +This and all associated files of various formats will be found in: + https://www.gutenberg.org/2/7/2/8/27286/ + +Produced by Steven Gibbs, Greg Bergquist and the Online +Distributed Proofreading Team at https://www.pgdp.net + + +Updated editions will replace the previous one--the old editions +will be renamed. + +Creating the works from public domain print editions means that no +one owns a United States copyright in these works, so the Foundation +(and you!) can copy and distribute it in the United States without +permission and without paying copyright royalties. Special rules, +set forth in the General Terms of Use part of this license, apply to +copying and distributing Project Gutenberg-tm electronic works to +protect the PROJECT GUTENBERG-tm concept and trademark. Project +Gutenberg is a registered trademark, and may not be used if you +charge for the eBooks, unless you receive specific permission. If you +do not charge anything for copies of this eBook, complying with the +rules is very easy. You may use this eBook for nearly any purpose +such as creation of derivative works, reports, performances and +research. They may be modified and printed and given away--you may do +practically ANYTHING with public domain eBooks. Redistribution is +subject to the trademark license, especially commercial +redistribution. + + + +*** START: FULL LICENSE *** + +THE FULL PROJECT GUTENBERG LICENSE +PLEASE READ THIS BEFORE YOU DISTRIBUTE OR USE THIS WORK + +To protect the Project Gutenberg-tm mission of promoting the free +distribution of electronic works, by using or distributing this work +(or any other work associated in any way with the phrase "Project +Gutenberg"), you agree to comply with all the terms of the Full Project +Gutenberg-tm License (available with this file or online at +https://gutenberg.org/license). + + +Section 1. General Terms of Use and Redistributing Project Gutenberg-tm +electronic works + +1.A. By reading or using any part of this Project Gutenberg-tm +electronic work, you indicate that you have read, understand, agree to +and accept all the terms of this license and intellectual property +(trademark/copyright) agreement. If you do not agree to abide by all +the terms of this agreement, you must cease using and return or destroy +all copies of Project Gutenberg-tm electronic works in your possession. +If you paid a fee for obtaining a copy of or access to a Project +Gutenberg-tm electronic work and you do not agree to be bound by the +terms of this agreement, you may obtain a refund from the person or +entity to whom you paid the fee as set forth in paragraph 1.E.8. + +1.B. "Project Gutenberg" is a registered trademark. It may only be +used on or associated in any way with an electronic work by people who +agree to be bound by the terms of this agreement. There are a few +things that you can do with most Project Gutenberg-tm electronic works +even without complying with the full terms of this agreement. See +paragraph 1.C below. There are a lot of things you can do with Project +Gutenberg-tm electronic works if you follow the terms of this agreement +and help preserve free future access to Project Gutenberg-tm electronic +works. See paragraph 1.E below. + +1.C. The Project Gutenberg Literary Archive Foundation ("the Foundation" +or PGLAF), owns a compilation copyright in the collection of Project +Gutenberg-tm electronic works. Nearly all the individual works in the +collection are in the public domain in the United States. If an +individual work is in the public domain in the United States and you are +located in the United States, we do not claim a right to prevent you from +copying, distributing, performing, displaying or creating derivative +works based on the work as long as all references to Project Gutenberg +are removed. Of course, we hope that you will support the Project +Gutenberg-tm mission of promoting free access to electronic works by +freely sharing Project Gutenberg-tm works in compliance with the terms of +this agreement for keeping the Project Gutenberg-tm name associated with +the work. You can easily comply with the terms of this agreement by +keeping this work in the same format with its attached full Project +Gutenberg-tm License when you share it without charge with others. + +1.D. The copyright laws of the place where you are located also govern +what you can do with this work. Copyright laws in most countries are in +a constant state of change. If you are outside the United States, check +the laws of your country in addition to the terms of this agreement +before downloading, copying, displaying, performing, distributing or +creating derivative works based on this work or any other Project +Gutenberg-tm work. The Foundation makes no representations concerning +the copyright status of any work in any country outside the United +States. + +1.E. Unless you have removed all references to Project Gutenberg: + +1.E.1. The following sentence, with active links to, or other immediate +access to, the full Project Gutenberg-tm License must appear prominently +whenever any copy of a Project Gutenberg-tm work (any work on which the +phrase "Project Gutenberg" appears, or with which the phrase "Project +Gutenberg" is associated) is accessed, displayed, performed, viewed, +copied or distributed: + +This eBook is for the use of anyone anywhere at no cost and with +almost no restrictions whatsoever. You may copy it, give it away or +re-use it under the terms of the Project Gutenberg License included +with this eBook or online at www.gutenberg.org + +1.E.2. If an individual Project Gutenberg-tm electronic work is derived +from the public domain (does not contain a notice indicating that it is +posted with permission of the copyright holder), the work can be copied +and distributed to anyone in the United States without paying any fees +or charges. If you are redistributing or providing access to a work +with the phrase "Project Gutenberg" associated with or appearing on the +work, you must comply either with the requirements of paragraphs 1.E.1 +through 1.E.7 or obtain permission for the use of the work and the +Project Gutenberg-tm trademark as set forth in paragraphs 1.E.8 or +1.E.9. + +1.E.3. If an individual Project Gutenberg-tm electronic work is posted +with the permission of the copyright holder, your use and distribution +must comply with both paragraphs 1.E.1 through 1.E.7 and any additional +terms imposed by the copyright holder. Additional terms will be linked +to the Project Gutenberg-tm License for all works posted with the +permission of the copyright holder found at the beginning of this work. + +1.E.4. Do not unlink or detach or remove the full Project Gutenberg-tm +License terms from this work, or any files containing a part of this +work or any other work associated with Project Gutenberg-tm. + +1.E.5. Do not copy, display, perform, distribute or redistribute this +electronic work, or any part of this electronic work, without +prominently displaying the sentence set forth in paragraph 1.E.1 with +active links or immediate access to the full terms of the Project +Gutenberg-tm License. + +1.E.6. You may convert to and distribute this work in any binary, +compressed, marked up, nonproprietary or proprietary form, including any +word processing or hypertext form. However, if you provide access to or +distribute copies of a Project Gutenberg-tm work in a format other than +"Plain Vanilla ASCII" or other format used in the official version +posted on the official Project Gutenberg-tm web site (www.gutenberg.org), +you must, at no additional cost, fee or expense to the user, provide a +copy, a means of exporting a copy, or a means of obtaining a copy upon +request, of the work in its original "Plain Vanilla ASCII" or other +form. Any alternate format must include the full Project Gutenberg-tm +License as specified in paragraph 1.E.1. + +1.E.7. Do not charge a fee for access to, viewing, displaying, +performing, copying or distributing any Project Gutenberg-tm works +unless you comply with paragraph 1.E.8 or 1.E.9. + +1.E.8. You may charge a reasonable fee for copies of or providing +access to or distributing Project Gutenberg-tm electronic works provided +that + +- You pay a royalty fee of 20% of the gross profits you derive from + the use of Project Gutenberg-tm works calculated using the method + you already use to calculate your applicable taxes. The fee is + owed to the owner of the Project Gutenberg-tm trademark, but he + has agreed to donate royalties under this paragraph to the + Project Gutenberg Literary Archive Foundation. Royalty payments + must be paid within 60 days following each date on which you + prepare (or are legally required to prepare) your periodic tax + returns. Royalty payments should be clearly marked as such and + sent to the Project Gutenberg Literary Archive Foundation at the + address specified in Section 4, "Information about donations to + the Project Gutenberg Literary Archive Foundation." + +- You provide a full refund of any money paid by a user who notifies + you in writing (or by e-mail) within 30 days of receipt that s/he + does not agree to the terms of the full Project Gutenberg-tm + License. You must require such a user to return or + destroy all copies of the works possessed in a physical medium + and discontinue all use of and all access to other copies of + Project Gutenberg-tm works. + +- You provide, in accordance with paragraph 1.F.3, a full refund of any + money paid for a work or a replacement copy, if a defect in the + electronic work is discovered and reported to you within 90 days + of receipt of the work. + +- You comply with all other terms of this agreement for free + distribution of Project Gutenberg-tm works. + +1.E.9. If you wish to charge a fee or distribute a Project Gutenberg-tm +electronic work or group of works on different terms than are set +forth in this agreement, you must obtain permission in writing from +both the Project Gutenberg Literary Archive Foundation and Michael +Hart, the owner of the Project Gutenberg-tm trademark. Contact the +Foundation as set forth in Section 3 below. + +1.F. + +1.F.1. Project Gutenberg volunteers and employees expend considerable +effort to identify, do copyright research on, transcribe and proofread +public domain works in creating the Project Gutenberg-tm +collection. Despite these efforts, Project Gutenberg-tm electronic +works, and the medium on which they may be stored, may contain +"Defects," such as, but not limited to, incomplete, inaccurate or +corrupt data, transcription errors, a copyright or other intellectual +property infringement, a defective or damaged disk or other medium, a +computer virus, or computer codes that damage or cannot be read by +your equipment. + +1.F.2. LIMITED WARRANTY, DISCLAIMER OF DAMAGES - Except for the "Right +of Replacement or Refund" described in paragraph 1.F.3, the Project +Gutenberg Literary Archive Foundation, the owner of the Project +Gutenberg-tm trademark, and any other party distributing a Project +Gutenberg-tm electronic work under this agreement, disclaim all +liability to you for damages, costs and expenses, including legal +fees. YOU AGREE THAT YOU HAVE NO REMEDIES FOR NEGLIGENCE, STRICT +LIABILITY, BREACH OF WARRANTY OR BREACH OF CONTRACT EXCEPT THOSE +PROVIDED IN PARAGRAPH F3. YOU AGREE THAT THE FOUNDATION, THE +TRADEMARK OWNER, AND ANY DISTRIBUTOR UNDER THIS AGREEMENT WILL NOT BE +LIABLE TO YOU FOR ACTUAL, DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE OR +INCIDENTAL DAMAGES EVEN IF YOU GIVE NOTICE OF THE POSSIBILITY OF SUCH +DAMAGE. + +1.F.3. LIMITED RIGHT OF REPLACEMENT OR REFUND - If you discover a +defect in this electronic work within 90 days of receiving it, you can +receive a refund of the money (if any) you paid for it by sending a +written explanation to the person you received the work from. If you +received the work on a physical medium, you must return the medium with +your written explanation. The person or entity that provided you with +the defective work may elect to provide a replacement copy in lieu of a +refund. If you received the work electronically, the person or entity +providing it to you may choose to give you a second opportunity to +receive the work electronically in lieu of a refund. If the second copy +is also defective, you may demand a refund in writing without further +opportunities to fix the problem. + +1.F.4. Except for the limited right of replacement or refund set forth +in paragraph 1.F.3, this work is provided to you 'AS-IS' WITH NO OTHER +WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO +WARRANTIES OF MERCHANTIBILITY OR FITNESS FOR ANY PURPOSE. + +1.F.5. Some states do not allow disclaimers of certain implied +warranties or the exclusion or limitation of certain types of damages. +If any disclaimer or limitation set forth in this agreement violates the +law of the state applicable to this agreement, the agreement shall be +interpreted to make the maximum disclaimer or limitation permitted by +the applicable state law. The invalidity or unenforceability of any +provision of this agreement shall not void the remaining provisions. + +1.F.6. INDEMNITY - You agree to indemnify and hold the Foundation, the +trademark owner, any agent or employee of the Foundation, anyone +providing copies of Project Gutenberg-tm electronic works in accordance +with this agreement, and any volunteers associated with the production, +promotion and distribution of Project Gutenberg-tm electronic works, +harmless from all liability, costs and expenses, including legal fees, +that arise directly or indirectly from any of the following which you do +or cause to occur: (a) distribution of this or any Project Gutenberg-tm +work, (b) alteration, modification, or additions or deletions to any +Project Gutenberg-tm work, and (c) any Defect you cause. + + +Section 2. Information about the Mission of Project Gutenberg-tm + +Project Gutenberg-tm is synonymous with the free distribution of +electronic works in formats readable by the widest variety of computers +including obsolete, old, middle-aged and new computers. It exists +because of the efforts of hundreds of volunteers and donations from +people in all walks of life. + +Volunteers and financial support to provide volunteers with the +assistance they need, is critical to reaching Project Gutenberg-tm's +goals and ensuring that the Project Gutenberg-tm collection will +remain freely available for generations to come. In 2001, the Project +Gutenberg Literary Archive Foundation was created to provide a secure +and permanent future for Project Gutenberg-tm and future generations. +To learn more about the Project Gutenberg Literary Archive Foundation +and how your efforts and donations can help, see Sections 3 and 4 +and the Foundation web page at https://www.pglaf.org. + + +Section 3. Information about the Project Gutenberg Literary Archive +Foundation + +The Project Gutenberg Literary Archive Foundation is a non profit +501(c)(3) educational corporation organized under the laws of the +state of Mississippi and granted tax exempt status by the Internal +Revenue Service. The Foundation's EIN or federal tax identification +number is 64-6221541. Its 501(c)(3) letter is posted at +https://pglaf.org/fundraising. Contributions to the Project Gutenberg +Literary Archive Foundation are tax deductible to the full extent +permitted by U.S. federal laws and your state's laws. + +The Foundation's principal office is located at 4557 Melan Dr. S. +Fairbanks, AK, 99712., but its volunteers and employees are scattered +throughout numerous locations. Its business office is located at +809 North 1500 West, Salt Lake City, UT 84116, (801) 596-1887, email +business@pglaf.org. Email contact links and up to date contact +information can be found at the Foundation's web site and official +page at https://pglaf.org + +For additional contact information: + Dr. Gregory B. Newby + Chief Executive and Director + gbnewby@pglaf.org + + +Section 4. Information about Donations to the Project Gutenberg +Literary Archive Foundation + +Project Gutenberg-tm depends upon and cannot survive without wide +spread public support and donations to carry out its mission of +increasing the number of public domain and licensed works that can be +freely distributed in machine readable form accessible by the widest +array of equipment including outdated equipment. Many small donations +($1 to $5,000) are particularly important to maintaining tax exempt +status with the IRS. + +The Foundation is committed to complying with the laws regulating +charities and charitable donations in all 50 states of the United +States. Compliance requirements are not uniform and it takes a +considerable effort, much paperwork and many fees to meet and keep up +with these requirements. We do not solicit donations in locations +where we have not received written confirmation of compliance. To +SEND DONATIONS or determine the status of compliance for any +particular state visit https://pglaf.org + +While we cannot and do not solicit contributions from states where we +have not met the solicitation requirements, we know of no prohibition +against accepting unsolicited donations from donors in such states who +approach us with offers to donate. + +International donations are gratefully accepted, but we cannot make +any statements concerning tax treatment of donations received from +outside the United States. U.S. laws alone swamp our small staff. + +Please check the Project Gutenberg Web pages for current donation +methods and addresses. Donations are accepted in a number of other +ways including including checks, online payments and credit card +donations. To donate, please visit: https://pglaf.org/donate + + +Section 5. General Information About Project Gutenberg-tm electronic +works. + +Professor Michael S. Hart was the originator of the Project Gutenberg-tm +concept of a library of electronic works that could be freely shared +with anyone. For thirty years, he produced and distributed Project +Gutenberg-tm eBooks with only a loose network of volunteer support. + + +Project Gutenberg-tm eBooks are often created from several printed +editions, all of which are confirmed as Public Domain in the U.S. +unless a copyright notice is included. Thus, we do not necessarily +keep eBooks in compliance with any particular paper edition. + + +Most people start at our Web site which has the main PG search facility: + + https://www.gutenberg.org + +This Web site includes information about Project Gutenberg-tm, +including how to make donations to the Project Gutenberg Literary +Archive Foundation, how to help produce our new eBooks, and how to +subscribe to our email newsletter to hear about new eBooks. + + +</pre> + +</body> +</html> diff --git a/27286-h/images/image1.jpg b/27286-h/images/image1.jpg Binary files differnew file mode 100644 index 0000000..3c5a25f --- /dev/null +++ b/27286-h/images/image1.jpg diff --git a/27286-h/images/image10.jpg b/27286-h/images/image10.jpg Binary files differnew file mode 100644 index 0000000..766476c --- /dev/null +++ b/27286-h/images/image10.jpg diff --git a/27286-h/images/image11.jpg b/27286-h/images/image11.jpg Binary files differnew file mode 100644 index 0000000..5d9f7d3 --- /dev/null +++ b/27286-h/images/image11.jpg diff --git a/27286-h/images/image12.jpg b/27286-h/images/image12.jpg Binary files differnew file mode 100644 index 0000000..aea5c3a --- /dev/null +++ b/27286-h/images/image12.jpg diff --git a/27286-h/images/image13.jpg b/27286-h/images/image13.jpg Binary files differnew file mode 100644 index 0000000..41c2853 --- /dev/null +++ b/27286-h/images/image13.jpg diff --git a/27286-h/images/image14.jpg b/27286-h/images/image14.jpg Binary files differnew file mode 100644 index 0000000..962313e --- /dev/null +++ b/27286-h/images/image14.jpg diff --git a/27286-h/images/image15.jpg b/27286-h/images/image15.jpg Binary files differnew file mode 100644 index 0000000..49edd05 --- /dev/null +++ b/27286-h/images/image15.jpg diff --git a/27286-h/images/image16.jpg b/27286-h/images/image16.jpg Binary files differnew file mode 100644 index 0000000..91ddc03 --- /dev/null +++ b/27286-h/images/image16.jpg diff --git a/27286-h/images/image17.jpg b/27286-h/images/image17.jpg Binary files differnew file mode 100644 index 0000000..bf74e1e --- /dev/null +++ b/27286-h/images/image17.jpg diff --git a/27286-h/images/image18.jpg b/27286-h/images/image18.jpg Binary files differnew file mode 100644 index 0000000..d03ac8a --- /dev/null +++ b/27286-h/images/image18.jpg diff --git a/27286-h/images/image19.jpg b/27286-h/images/image19.jpg Binary files differnew file mode 100644 index 0000000..815f467 --- /dev/null +++ b/27286-h/images/image19.jpg diff --git a/27286-h/images/image2.jpg b/27286-h/images/image2.jpg Binary files differnew file mode 100644 index 0000000..7306a4a --- /dev/null +++ b/27286-h/images/image2.jpg diff --git a/27286-h/images/image20.jpg b/27286-h/images/image20.jpg Binary files differnew file mode 100644 index 0000000..11fbcc4 --- /dev/null +++ b/27286-h/images/image20.jpg diff --git a/27286-h/images/image21.jpg b/27286-h/images/image21.jpg Binary files differnew file mode 100644 index 0000000..b4e01f6 --- /dev/null +++ b/27286-h/images/image21.jpg diff --git a/27286-h/images/image22.jpg b/27286-h/images/image22.jpg Binary files differnew file mode 100644 index 0000000..94395ef --- /dev/null +++ b/27286-h/images/image22.jpg diff --git a/27286-h/images/image23.jpg b/27286-h/images/image23.jpg Binary files differnew file mode 100644 index 0000000..6709bfe --- /dev/null +++ b/27286-h/images/image23.jpg diff --git a/27286-h/images/image24.jpg b/27286-h/images/image24.jpg Binary files differnew file mode 100644 index 0000000..a9c8e34 --- /dev/null +++ b/27286-h/images/image24.jpg diff --git a/27286-h/images/image25.jpg b/27286-h/images/image25.jpg Binary files differnew file mode 100644 index 0000000..bc93593 --- /dev/null +++ b/27286-h/images/image25.jpg diff --git a/27286-h/images/image26.jpg b/27286-h/images/image26.jpg Binary files differnew file mode 100644 index 0000000..1383c9f --- /dev/null +++ b/27286-h/images/image26.jpg diff --git a/27286-h/images/image27.jpg b/27286-h/images/image27.jpg Binary files differnew file mode 100644 index 0000000..7d064ba --- /dev/null +++ b/27286-h/images/image27.jpg diff --git a/27286-h/images/image28.jpg b/27286-h/images/image28.jpg Binary files differnew file mode 100644 index 0000000..f5b03d9 --- /dev/null +++ b/27286-h/images/image28.jpg diff --git a/27286-h/images/image29.jpg b/27286-h/images/image29.jpg Binary files differnew file mode 100644 index 0000000..a22e95b --- /dev/null +++ b/27286-h/images/image29.jpg diff --git a/27286-h/images/image3.jpg b/27286-h/images/image3.jpg Binary files differnew file mode 100644 index 0000000..ec4aefe --- /dev/null +++ b/27286-h/images/image3.jpg diff --git a/27286-h/images/image30.jpg b/27286-h/images/image30.jpg Binary files differnew file mode 100644 index 0000000..9683dab --- /dev/null +++ b/27286-h/images/image30.jpg diff --git a/27286-h/images/image31.jpg b/27286-h/images/image31.jpg Binary files differnew file mode 100644 index 0000000..e275b90 --- /dev/null +++ b/27286-h/images/image31.jpg diff --git a/27286-h/images/image32.jpg b/27286-h/images/image32.jpg Binary files differnew file mode 100644 index 0000000..fb75239 --- /dev/null +++ b/27286-h/images/image32.jpg diff --git a/27286-h/images/image33.jpg b/27286-h/images/image33.jpg Binary files differnew file mode 100644 index 0000000..3d6f910 --- /dev/null +++ b/27286-h/images/image33.jpg diff --git a/27286-h/images/image34.jpg b/27286-h/images/image34.jpg Binary files differnew file mode 100644 index 0000000..022c5f8 --- /dev/null +++ b/27286-h/images/image34.jpg diff --git a/27286-h/images/image35.jpg b/27286-h/images/image35.jpg Binary files differnew file mode 100644 index 0000000..acd7f51 --- /dev/null +++ b/27286-h/images/image35.jpg diff --git a/27286-h/images/image36.jpg b/27286-h/images/image36.jpg Binary files differnew file mode 100644 index 0000000..f28f28e --- /dev/null +++ b/27286-h/images/image36.jpg diff --git a/27286-h/images/image37.jpg b/27286-h/images/image37.jpg Binary files differnew file mode 100644 index 0000000..8b9c606 --- /dev/null +++ b/27286-h/images/image37.jpg diff --git a/27286-h/images/image38.jpg b/27286-h/images/image38.jpg Binary files differnew file mode 100644 index 0000000..918628e --- /dev/null +++ b/27286-h/images/image38.jpg diff --git a/27286-h/images/image39.jpg b/27286-h/images/image39.jpg Binary files differnew file mode 100644 index 0000000..f677738 --- /dev/null +++ b/27286-h/images/image39.jpg diff --git a/27286-h/images/image4.jpg b/27286-h/images/image4.jpg Binary files differnew file mode 100644 index 0000000..0fc4ca4 --- /dev/null +++ b/27286-h/images/image4.jpg diff --git a/27286-h/images/image40.jpg b/27286-h/images/image40.jpg Binary files differnew file mode 100644 index 0000000..8b47552 --- /dev/null +++ b/27286-h/images/image40.jpg diff --git a/27286-h/images/image40a.jpg b/27286-h/images/image40a.jpg Binary files differnew file mode 100644 index 0000000..d69e576 --- /dev/null +++ b/27286-h/images/image40a.jpg diff --git a/27286-h/images/image41.jpg b/27286-h/images/image41.jpg Binary files differnew file mode 100644 index 0000000..533ec35 --- /dev/null +++ b/27286-h/images/image41.jpg diff --git a/27286-h/images/image42.jpg b/27286-h/images/image42.jpg Binary files differnew file mode 100644 index 0000000..50e1e07 --- /dev/null +++ b/27286-h/images/image42.jpg diff --git a/27286-h/images/image43.jpg b/27286-h/images/image43.jpg Binary files differnew file mode 100644 index 0000000..0267770 --- /dev/null +++ b/27286-h/images/image43.jpg diff --git a/27286-h/images/image44.jpg b/27286-h/images/image44.jpg Binary files differnew file mode 100644 index 0000000..fe75f30 --- /dev/null +++ b/27286-h/images/image44.jpg diff --git a/27286-h/images/image45.jpg b/27286-h/images/image45.jpg Binary files differnew file mode 100644 index 0000000..586e515 --- /dev/null +++ b/27286-h/images/image45.jpg diff --git a/27286-h/images/image46.jpg b/27286-h/images/image46.jpg Binary files differnew file mode 100644 index 0000000..cd9145f --- /dev/null +++ b/27286-h/images/image46.jpg diff --git a/27286-h/images/image47.jpg b/27286-h/images/image47.jpg Binary files differnew file mode 100644 index 0000000..c1b5d5c --- /dev/null +++ b/27286-h/images/image47.jpg diff --git a/27286-h/images/image48.jpg b/27286-h/images/image48.jpg Binary files differnew file mode 100644 index 0000000..4c6221a --- /dev/null +++ b/27286-h/images/image48.jpg diff --git a/27286-h/images/image49.jpg b/27286-h/images/image49.jpg Binary files differnew file mode 100644 index 0000000..9d24f97 --- /dev/null +++ b/27286-h/images/image49.jpg diff --git a/27286-h/images/image5.jpg b/27286-h/images/image5.jpg Binary files differnew file mode 100644 index 0000000..41d7e80 --- /dev/null +++ b/27286-h/images/image5.jpg diff --git a/27286-h/images/image50.jpg b/27286-h/images/image50.jpg Binary files differnew file mode 100644 index 0000000..43a1009 --- /dev/null +++ b/27286-h/images/image50.jpg diff --git a/27286-h/images/image51.jpg b/27286-h/images/image51.jpg Binary files differnew file mode 100644 index 0000000..c01be5b --- /dev/null +++ b/27286-h/images/image51.jpg diff --git a/27286-h/images/image6.jpg b/27286-h/images/image6.jpg Binary files differnew file mode 100644 index 0000000..861607f --- /dev/null +++ b/27286-h/images/image6.jpg diff --git a/27286-h/images/image7.jpg b/27286-h/images/image7.jpg Binary files differnew file mode 100644 index 0000000..9102621 --- /dev/null +++ b/27286-h/images/image7.jpg diff --git a/27286-h/images/image8.jpg b/27286-h/images/image8.jpg Binary files differnew file mode 100644 index 0000000..ed37ef8 --- /dev/null +++ b/27286-h/images/image8.jpg diff --git a/27286-h/images/image9.jpg b/27286-h/images/image9.jpg Binary files differnew file mode 100644 index 0000000..c27f189 --- /dev/null +++ b/27286-h/images/image9.jpg |
